Husqvarna TS 242TXD User Manual (English)

Other manuals for Husqvarna TS 242TXD

Questions and Answers:

N
nelsondebraAug 23, 2025
What to do if starter motor does not turn the engine over on Husqvarna Lawn Mower?
- L
  Latoya HarrellAug 23, 2025
  If the starter motor on your Husqvarna Lawn Mower isn't turning the engine over, several things could be the cause. First, ensure the battery isn't too weak by charging it. Make sure the attachment clutch control is disengaged. Also, verify that the clutch/brake pedal is fully pushed down when starting the engine. Check the battery connections for any issues. Other potential issues include a damaged main fuse (replace it). For a damaged ignition lock, safety connector for clutch/brake pedal, or starter motor/solenoid, it is recommended to consult a service agent. Also, if the operator presence control (OPC) does not operate correctly, check the wires, switches and connections and consult a service agent.
R
Randy AdamsAug 26, 2025
What to do if Husqvarna Lawn Mower battery does not charge?
- D
  Deborah BensonAug 26, 2025
  If your Husqvarna Lawn Mower battery isn't charging, several things could be the cause. First, check if the main fuse is damaged and replace it if necessary. If the battery is damaged, replace it. Ensure the charging cable is connected properly. Also, check the battery connections for any issues.
N
Nancy EspinozaAug 28, 2025
What to do if Husqvarna TS 242TXD engine becomes too hot?
- M
  marissa47Aug 28, 2025
  If your Husqvarna Lawn Mower engine is overheating, there are several things to consider. First, check if there is an overload in the engine and decrease the workload. Make sure that the air intake or the cooling fins on the engine are not blocked; if they are, clean them. Also, check the engine oil level and add oil if necessary. Other potential issues include a damaged spark plug (replace the spark plug). For a damaged cooling fan or ignition lock, it is recommended to consult a service agent.
P
pollardlisaSep 2, 2025
Why is the cutting result unsatisfactory with my Husqvarna TS 242TXD Lawn Mower?
- M
  Matthew MillerSep 2, 2025
  If you're not satisfied with the cutting result from your Husqvarna Lawn Mower, several factors could be the cause. Start by checking if the blades are blunt or damaged and sharpen or replace them as needed. If the cutting deck is not parallel, adjust it. Avoid cutting when the grass is wet. If the grass is long, begin with a high cutting height and gradually decrease it. Check the tire pressure and adjust it if necessary. Also, avoid operating the product at too high a forward or rearward speed; use a slower speed. A worn or damaged drive belt for the cutting deck (replace it).
T
Taylor NolanSep 4, 2025
Why is there vibration in my Husqvarna TS 242TXD?
- A
  Alex MclaughlinSep 4, 2025
  If you're experiencing vibration in your Husqvarna Lawn Mower, several factors could be the cause. Start by checking if the blades are loose and tighten the bolts. Also, inspect the blades for damage or imbalance and balance or replace them as necessary. Finally, make sure that the engine is not loose and tighten the engine bolts.
T
Tanya HillSep 7, 2025
Why does my Husqvarna TS 242TXD Lawn Mower move slowly or not at all?
- M
  macdonaldamySep 7, 2025
  If your Husqvarna Lawn Mower is moving slowly, irregularly, or not at all, several factors could be the cause. First, check if the product is in freewheel mode. Also, verify that the parking brake is disengaged. Other potential issues include a loose or damaged drive belt (replace it), unwanted materials on the steering plate (clean the product), or a missing square key on the axle.
J
Jessica WhiteSep 10, 2025
Why can't the blades rotate on my Husqvarna TS 242TXD Lawn Mower?
- J
  Joshua HudsonSep 10, 2025
  If the blades on your Husqvarna Lawn Mower aren't rotating, several issues could be the cause. Check for any blockage in the clutch mechanism and remove it. Other potential issues include a worn or damaged drive belt for the cutting deck (replace it), a frozen idler pulley (replace the idler pulley), or a frozen blade mandrel (replace the blade mandrel).

Husqvarna TS 242TXD Specifications

General

Engine Displacement	725 cc
Cylinders	2
Cutting Width	42 in
Cutting Height, Max	4 in
Transmission Type	Automatic
Transmission Manufacturer	Hydro-Gear
Drive	Rear-wheel drive
Blade Engagement	Electric
Turning Radius	16 in
Seat Type	High back
Deck Material	Steel
Speed	5.5 mph
Warranty	3 years
Engine	Kohler
Engine Type	4-cycle
Cutting Height, Min	1.5 in
Fuel Capacity	3.5 gal

Summary

Introduction to the Husqvarna TS 242TXD

Pre-Delivery Inspection and Product Identification

Details on pre-delivery checks and recording product identification numbers.

Product Description and Specifications

Overview of the lawn tractor's features, engine, and optional accessories.

Intended Use of the Riding Mower

Defines the proper applications and limitations for the lawn tractor's operation.

Customer Support and Assistance

Information on how to obtain help, contact details, and website resources.

Product Overview and Symbols

Product Overview Diagram

Labeled diagram identifying key components and controls of the product.

Product Symbols Guide

Explanation of warning and informational symbols used on the product.

Comprehensive Safety Guidelines

Safety Definitions and Warnings

Clarifies the meaning of WARNING, CAUTION, and Note in the manual.

Safe Operation Practices for Ride-On Mowers

Essential safety rules for operating riding lawn mowers safely.

Specific Safety Information

Children Safety Guidelines

Recommendations regarding age limits and supervision for child operation.

General Operation Safety Instructions

Key safety precautions for general use and operation of the machine.

Safety Procedures and Checks

Safety Instructions for Operation

Guidelines for safe operation, including personal protective equipment (PPE).

Personal Protective Equipment (PPE)

Recommendations for wearing appropriate PPE during operation and maintenance.

Safety Devices on the Product

Ensuring safety devices are functional and not modified for safe operation.

Operator Presence Control (OPC) Check

Procedure to verify the correct functioning of the operator presence control system.

Reverse Operation System (ROS) Check

Procedure to verify the correct functioning of the reverse operation system.

Specific Safety Operations

Brake System Safety

Safety precautions and checks related to the product's braking system.

Parking Brake Operation

Ensuring the parking brake functions correctly to prevent unintended movement.

Muffler Safety Information

Warnings regarding hot surfaces and fire risks associated with the muffler.

Cutting Grass on Slopes Safely

Guidelines for safely cutting grass on inclines and slopes.

Fuel Safety Precautions

Essential safety rules for handling and refueling flammable fuel.

Additional Safety Topics

Battery Safety Precautions

Safety guidelines for handling and charging the product's battery.

Transport Safety Guidelines

Safety considerations when transporting the product via a vehicle.

Safety Instructions for Maintenance

Crucial safety advice before performing any maintenance tasks on the product.

Assembly Procedures

Introduction to Assembly

Overview and safety warnings before beginning product assembly.

Removing Product from Carton

Step-by-step guide for safely unpacking the product from its packaging.

Required Assembly Tools

List of tools needed to complete the assembly process.

Loose Parts Identification

Identifies parts that are shipped separately and require assembly.

Adjusting the Seat Position

Instructions for adjusting the seat for optimal operator comfort and control.

Battery and Initial Setup

Connecting the Battery

Step-by-step instructions for safely connecting the product's battery.

Moving Product Off Skid

Procedure for safely removing the product from its shipping skid.

Post-Assembly Checks

Essential checks to perform after assembly to ensure safe operation.

Operation: Starting and Fueling

Starting a Warm Engine

Procedure for starting the engine when it is already warm.

Filling the Fuel Tank

Instructions and safety precautions for refueling the product.

Starting the Product

General steps required before starting the engine.

Starting a Cold Engine

Procedure for starting the engine when it is cold.

Operating Procedures

Setting the Cutting Height

Instructions on how to adjust the cutting deck to the desired height.

Moving Product Forward and Rearward

How to control the product's movement using the drive pedals.

Cutting Deck Transport/Mow Position

Setting the cutting deck for transport or mowing.

Controls and Stopping Procedures

Engaging and Disengaging Parking Brake

Steps to correctly engage and disengage the parking brake.

Stopping the Product Safely

Procedure for safely stopping the engine and securing the product.

Using the Throttle Control

How to operate the throttle control for optimal engine speed and cutting.

Using the Choke Control

Instructions for using the choke to start a cold engine.

Advanced Operation Features

Using the Cruise Control

How to engage and use the cruise control for consistent forward speed.

Headlight Operation

Instructions for turning the headlights on and off.

Engaging and Disengaging the Cutting Deck

Procedure for engaging and disengaging the cutting deck.

Using the Reverse Operation System (ROS)

How to enable reverse operation with the cutting deck engaged.

Achieving Good Cutting Results

Tips for obtaining the best cutting performance from the mower.

Freewheel Mode Operation

Putting Product in Freewheel Mode

Steps to disengage the transmission for towing or manual movement.

Maintenance Introduction

Introduction to Maintenance

General safety warnings and advice before performing maintenance.

Cleaning and Washing Procedures

Cleaning the Product

Instructions for cleaning the exterior surfaces of the product.

Using the Deck Washout Port

Procedure for using the deck washout port to clean the cutting deck.

Component Maintenance and Checks

Throttle Control Cable Adjustment

Guidance on adjusting the throttle control cable if necessary.

Interlocks and Relays Examination

Checking wiring for proper function and potential damage.

LED Headlight Replacement

Steps for replacing the LED headlight assembly.

Tire Checks and Maintenance

Ensuring correct tire pressure and inspecting tires for damage.

Tire Repair Procedures

Instructions for repairing tires, including sealing small holes.

V-Belts Examination

Inspecting V-belts for wear and deterioration.

Transaxle Cooling Fan Maintenance

Keeping the transaxle cooling fan and fins clean for proper cooling.

Further Maintenance Procedures

Transaxle Pump Fluid Check

Checking the transaxle pump fluid level and for leaks.

Front Wheel Toe-in/Camber Adjustment

Information on front wheel alignment settings.

Fuse Replacement

Procedure for replacing a blown fuse.

Engine Cover and Grill Assembly

Instructions for removing and installing the engine cover and grill.

Motion Drive Belt Replacement

Steps for replacing the main drive belt.

Battery Maintenance and Service

Cleaning Battery and Terminals

Procedure for cleaning battery corrosion and terminals.

Replacing the Battery

Steps for safely removing and installing a new battery.

Connecting Jumper Cables

Instructions for jump-starting the product's battery.

Cutting Deck Maintenance

Removing and Installing the Cutting Deck

Detailed steps for detaching and reattaching the cutting deck assembly.

Adjusting Cutting Deck Parallelism

Ensuring the cutting deck is level side-to-side.

Visual Side-to-Side Cutting Deck Adjustment

Procedure for visually aligning the cutting deck for even cuts.

Cutting Deck Adjustment Procedures

Precision Side-to-Side Cutting Deck Adjustment

Detailed procedure for precise side-to-side cutting deck alignment.

Front-to-Rear Cutting Deck Adjustment

Procedure for adjusting the cutting deck for proper front-to-rear pitch.

Blade and Belt Maintenance

Replacing Cutting Deck Blades

Instructions for safely replacing worn or damaged cutting blades.

Removing Cutting Deck Drive Belt

Steps to safely remove the drive belt from the cutting deck.

Installing Cutting Deck Drive Belt

Procedure for correctly installing the cutting deck drive belt.

Adjusting Anti-Scalp Rollers

How to adjust anti-scalp rollers for optimal ground contact.

Engine Maintenance

Lubricating the Engine

Guidelines for lubricating engine components with appropriate oils.

Changing Engine Oil

Procedure for draining and refilling the engine oil.

Checking Engine Oil Level

How to properly check the engine oil level.

Engine Servicing Procedures

Engine Oil Filter Replacement

Steps for replacing the engine oil filter.

Air Filter Cleaning

Instructions for cleaning or replacing the air filter.

Air Screen Cleaning

Procedure for cleaning the engine's air screen.

Engine Cooling System Maintenance

Ensuring the engine cooling system is clean and functional.

Muffler Maintenance

Inspecting the muffler for corrosion and damage.

Spark Plug Replacement

Instructions for replacing the spark plug.

Fuel and Transmission Systems

In-line Fuel Filter Replacement

Procedure for replacing the in-line fuel filter.

Removing Air from Transmission

Steps to bleed air from the transmission system.

Troubleshooting: Engine Start Issues

Engine Does Not Start

Common causes and actions for when the engine fails to start.

Starter Motor Issues

Troubleshooting steps for when the starter motor does not turn the engine.

Troubleshooting: Engine Performance

Engine Running Smoothly

Causes and solutions for an engine that does not run smoothly.

Engine Overheating

Diagnosing and resolving issues causing the engine to overheat.

Troubleshooting: Power, Vibration, and Battery

Loss of Power

Identifying causes for reduced power output and solutions.

Product Vibration

Troubleshooting excessive vibration in the product.

Battery Charging Problems

Diagnosing why the battery is not charging correctly.

Troubleshooting: Operational Faults

Operator Presence Control Fault

Addressing issues where the engine operates unexpectedly with the seat vacant.

Blade Rotation Issues

Diagnosing problems when the cutting blades cannot rotate.

Grass Discharge Problems

Troubleshooting issues related to damaged or unsatisfactory grass discharge.

Headlight Malfunction

Resolving issues where the headlight does not function.

Troubleshooting: Movement and Cutting

Slow or Irregular Movement

Causes and solutions for slow, irregular, or no product movement.

Unsatisfactory Cutting Result

Addressing issues leading to poor cutting performance.

Engine Backfire

Diagnosing engine backfire when the engine stops.

Engine Stops During Reverse

Troubleshooting why the engine stops when attempting to reverse.

Transportation, Storage, and Disposal

Transportation Guidelines

Procedures and safety advice for transporting the product.

Product Storage Procedures

Instructions for preparing and storing the product for extended periods.

Product Disposal Guidelines

Environmentally responsible methods for disposing of the product and its components.

Technical Data

Service and Parts Information

Authorized Service Center Recommendations

Advice on seeking professional service and ordering spare parts.

Guide for Sighting Slopes

Related product manuals

Husqvarna TS 238 Euro

92 pages

Husqvarna TS 354XD 2022

Husqvarna TS 242TXD User Manual

Table of Contents

Other manuals for Husqvarna TS 242TXD

Questions and Answers:

Husqvarna TS 242TXD Specifications

Summary

Introduction to the Husqvarna TS 242TXD

Pre-Delivery Inspection and Product Identification

Product Description and Specifications

Intended Use of the Riding Mower

Customer Support and Assistance

Product Overview and Symbols

Product Overview Diagram

Product Symbols Guide

Comprehensive Safety Guidelines

Safety Definitions and Warnings

Safe Operation Practices for Ride-On Mowers

Specific Safety Information

Children Safety Guidelines

General Operation Safety Instructions

Safety Procedures and Checks

Safety Instructions for Operation

Personal Protective Equipment (PPE)

Safety Devices on the Product

Operator Presence Control (OPC) Check

Reverse Operation System (ROS) Check

Specific Safety Operations

Brake System Safety

Parking Brake Operation

Muffler Safety Information

Cutting Grass on Slopes Safely

Fuel Safety Precautions

Additional Safety Topics

Battery Safety Precautions

Transport Safety Guidelines

Safety Instructions for Maintenance

Assembly Procedures

Introduction to Assembly

Removing Product from Carton

Required Assembly Tools

Loose Parts Identification

Adjusting the Seat Position

Battery and Initial Setup

Connecting the Battery

Moving Product Off Skid

Post-Assembly Checks

Operation: Starting and Fueling

Starting a Warm Engine

Filling the Fuel Tank

Starting the Product

Starting a Cold Engine

Operating Procedures

Setting the Cutting Height

Moving Product Forward and Rearward

Cutting Deck Transport/Mow Position

Controls and Stopping Procedures

Engaging and Disengaging Parking Brake

Stopping the Product Safely

Using the Throttle Control

Using the Choke Control

Advanced Operation Features

Using the Cruise Control

Headlight Operation

Engaging and Disengaging the Cutting Deck

Using the Reverse Operation System (ROS)

Achieving Good Cutting Results

Freewheel Mode Operation

Putting Product in Freewheel Mode

Maintenance Introduction

Introduction to Maintenance

Cleaning and Washing Procedures

Cleaning the Product

Using the Deck Washout Port

Component Maintenance and Checks

Throttle Control Cable Adjustment

Interlocks and Relays Examination

LED Headlight Replacement

Tire Checks and Maintenance

Tire Repair Procedures

V-Belts Examination