Husqvarna VIKING Designer Jade

Need help?

Do you have a question about the Husqvarna VIKING Designer Jade and is the answer not in the manual?

Summary

1. MOTOR BELT TENSION

2. TIMING BELT TENSION

3. BACKLASH OF HOOK GEAR

4. TIMING OF THE UPPER AND LOWER SHAFT

5. GAP BETWEEN NEEDLE AND HOOK

6. SETTING THE FEED DOG

7. HEIGHT OF THE FEED DOG

8. HEIGHT AND DIRECTION OF PRESSER FOOT

9. NEEDLE PLATE AND NEEDLE POSITION

Calibration Point

Checks and adjusts the calibration point for needle position.

Centre position

Checks and adjusts the center position of the needle.

10. POSITION OF NEEDLE POINT LIMITING PLATE

11. HEIGHT OF NEEDLE BAR

12. HEIGHT OF NEEDLE THREADER

13. TIMING OF THE HOOK

14. ADJUSTING THE FEED REGULATOR

15. ADJUSTING THE FORWARD REVERSE STITCH

16. ADJUSTING THE LOWER THREAD TENSION

17. UPPER THREAD TENSION

STEP 1

Checks the projection alignment for thread tension calibration.

STEP 2

Checks thread tension resistance in adjusting mode.

18. FLATNESS OF THE BASE

19. ADJUSTMENTS FOR BUTTONHOLE LEVER POSITION

20. BOBBIN WINDER

BOBBIN WINDS

Adjustments for uneven bobbin winding.

BOBBIN THREAD

Adjustments for bobbin thread winding amount.

Service Menu 1 - Stepper Motors

Service Menu 2 - Display Test, Sensors Test, Reset Functions

Display test 1

Checks for dead pixels on the display.

Display test 2

Adjusts the default contrast of the machine display.

Sensors test 1

Checks the synchronizer sensors (speed, timing, stop).

Sensors test 2

Sensors test 3

Sensors test 4

Reset functions 1

Reset functions 2

Service Menu 3 - Default Tension Adjustment, Test Pattern

Service Menu 4 - Test Pattern

Service Menu 5 - Keyboard Test

Embroidery Service Menu Function No.1 - Embroidery Test

Attached hoop

Shows the current attached hoop status.

Embroidery unit

Shows the currently attached embroidery unit.

Embroidery Service Menu Function No.2 - Embroidery Test

Embroidery Service Menu Function No.3 - Test Design

Embroidery Service Menu Function No.4 - Tension Adjustment

Electrical Parts Connection

REMOVING THE EXTERIOR PARTS

A. Light Cover

Procedure for removing the machine's light cover.

B. Thread Tension Cover

Procedure for removing the thread tension cover.

C. Needle Plate

Procedure for removing the needle plate.

D. Base

Procedure for removing the machine's base.

E. Front Enclosure

Procedure for removing the front enclosure.

F. Unit Cover

Procedure for removing the unit cover.

G. Top Cover

Procedure for removing the top cover.

H. Rear Enclosure

Procedure for removing the rear enclosure.

REPLACE THE EXTERIOR PARTS

H. Rear Enclosure

Procedure for replacing the rear enclosure.

G. Top Cover

Procedure for replacing the top cover.

F. Unit Cover

Procedure for replacing the unit cover.

E. Front Enclosure

Procedure for replacing the front enclosure.

D. Base

Procedure for replacing the machine's base.

C. Needle Plate

Procedure for replacing the needle plate.

B. Thread Tension Cover

Procedure for replacing the thread tension cover.

A. Light Cover

Procedure for replacing the machine's light cover.

EMBROIDERY UNIT

REMOVING THE EXTERIOR PARTS

Procedures for removing exterior parts of the embroidery unit.

A. Y carriage cover A

Procedure for removing the Y carriage cover A.

B. Y carriage cover B

Procedure for removing the Y carriage cover B.

C. X top cover

Procedure for removing the X top cover.

REPLACING THE EXTERIOR PARTS

C. X top cover

Procedure for replacing the X top cover.

B. Y carriage cover B

Procedure for replacing the Y carriage cover B.

A. Y carriage cover A

Procedure for replacing the Y carriage cover A.