HYDE QuickReach 28670

Questions and Answers

D
Debra FarrellAug 16, 2025
What to do if my HYDE QuickReach 28670 Tools spray gun doesn’t shut off?
- N
  nsilvaAug 16, 2025
  If your HYDE Tools spray gun doesn't shut off, it might be because the spray gun trigger lock is engaged. To resolve this, simply release the spray gun trigger lock.
B
Barbara GentryAug 19, 2025
Why is it difficult to pull the remote trigger on my HYDE QuickReach 28670?
- C
  Christy PopeAug 19, 2025
  If you're finding it hard to pull the remote trigger on your HYDE Tools, the cable hold-down wing nut might be loose or misadjusted. Try adjusting and retightening the cable hold-down wing nut to fix this.
D
Daniel TuckerAug 22, 2025
What to do if the remote trigger does not pull the trigger on the HYDE QuickReach 28670 spray gun?
- J
  Joseph Johnson IIIAug 22, 2025
  If the remote trigger on your HYDE Tools isn't pulling the spray gun trigger (or is only slightly pulling), it could be due to a faulty cable wire or remote trigger. The solution is to replace the wire or the remote trigger.
M
Martha GarciaAug 25, 2025
How to slide the spray gun mount into the pole of HYDE Tools?
- B
  Benjamin MurphyAug 26, 2025
  If the spray gun mount on your HYDE Tools won't slide into the pole, check the orientation of the spray gun mount connector housing. Align the hole in the spray gun mount connector housing with the latch lever on the pole.
M
myoungAug 28, 2025
What to do if I cannot remove the spray gun mount from the pole of my HYDE Tools?
- N
  nathaniel29Aug 28, 2025
  If you're unable to remove the spray gun mount from the pole of your HYDE Tools, make sure you're depressing the locking lever on the docking station while removing the spray gun mount.
B
brownjeanAug 31, 2025
Why the head assembly will not stay in place on my HYDE QuickReach 28670 Tools?
- D
  deborahallenAug 31, 2025
  If the head assembly of your HYDE Tools won't stay in place, it's likely that the release button isn't properly seated. Ensure that the release button is fully seated.
D
Debbie RogersSep 3, 2025
What to do if the pole will not telescope on my HYDE QuickReach 28670?
- W
  wholtSep 3, 2025
  If the pole of your HYDE Tools won't telescope, the telescoping lock collar might be loose. To fix this, loosen the locking collar, slightly extend the telescoping pole, then tighten the locking collar and pull the lever.
S
Sarah MckenzieSep 6, 2025
Why the remote trigger will not pull spray gun trigger on my HYDE QuickReach 28670 Tools?
- R
  rhonda96Sep 6, 2025
  If the remote trigger of your HYDE Tools will not pull the spray gun trigger, it could be that the head assembly is set up for the wrong spray gun. Try reassembling the head.
H
Heather EspinozaSep 9, 2025
Why standoff doesn’t move on my HYDE QuickReach 28670?
- P
  Paul BurchSep 9, 2025
  If the standoff on your HYDE Tools doesn’t move, it might be because the fluid hose isn't properly secured by the hose clips. Make sure to secure the fluid hose to the hose clips.
K
Karen CooperSep 12, 2025
Why is there a ratcheting noise when adjusting the length of my HYDE Tools?
- C
  Catherine HessSep 12, 2025
  Some ratcheting noise is normal when adjusting the length of HYDE Tools, especially on longer models. This shouldn't be a cause for concern as long as the spray pole functions properly.