HYDOM 3LC50 400A3A Series - Linear S Series Actuator Settings; Blocking Setting Adjustment; Speed Adjustment

LINEAL «S» SERIES ACTUATORS. BLOCKING SETTING.
Hydom Series “S” hydraulic operators are factory configured with double blocking,
To set up other configurations, open or
of the operator (see picture 1)
Picture 1. Valve A (under red screw). Valve B (under green screw)
LINEAL «S» SERIES ACTUATORS. SPEED ADJUSTMENT.
Hydom Series “S” hydraulic operators are Factory set at high speed extension and retraction.
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side
picture 2).
Picture 2. Speed adjusting valve
Door type
Blocking type
Valve A
Valve B
Speed
adjusting
scre
LINEAL «S» SERIES ACTUATORS. BLOCKING SETTING.
Hydom Series “S” hydraulic operators are factory configured with double blocking,
To set up other configurations, open or
of the operator (see picture 1)
Picture 1. Valve A (under red screw). Valve B (under green screw)
LINEAL «S» SERIES ACTUATORS. SPEED ADJUSTMENT.
Hydom Series “S” hydraulic operators are Factory set at high speed extension and retraction.
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side
picture 2).
Picture 2. Speed adjusting valve
Door type
Blocking type
Valve A
Valve B
Speed
adjusting
scre
Valve A
Valve B
LINEAL «S» SERIES ACTUATORS. BLOCKING SETTING.
Hydom Series “S” hydraulic operators are factory configured with double blocking,
To set up other configurations, open or
of the operator (see picture 1)
Picture 1. Valve A (under red screw). Valve B (under green screw)
LINEAL «S» SERIES ACTUATORS. SPEED ADJUSTMENT.
Hydom Series “S” hydraulic operators are Factory set at high speed extension and retraction.
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side
Picture 2. Speed adjusting valve
Without
locking
Open
Open
Valve A
Valve B
LINEAL «S» SERIES ACTUATORS. BLOCKING SETTING.
Hydom Series “S” hydraulic operators are factory configured with double blocking,
To set up other configurations, open or
close valves A and/or B using a 4mm Allen (hexagonal) wrench. Both valves are located on the bottom side
Picture 1. Valve A (under red screw). Valve B (under green screw)
LINEAL «S» SERIES ACTUATORS. SPEED ADJUSTMENT.
Hydom Series “S” hydraulic operators are Factory set at high speed extension and retraction.
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side
Without
locking
Open
Open
LINEAL «S» SERIES ACTUATORS. BLOCKING SETTING.
Hydom Series “S” hydraulic operators are factory configured with double blocking,
close valves A and/or B using a 4mm Allen (hexagonal) wrench. Both valves are located on the bottom side

Valve closed

Valve open
Picture 1. Valve A (under red screw). Valve B (under green screw)
LINEAL «S» SERIES ACTUATORS. SPEED ADJUSTMENT.
Hydom Series “S” hydraulic operators are Factory set at high speed extension and retraction.
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side


Double
blocking
Closed
Closed
10
LINEAL «S» SERIES ACTUATORS. BLOCKING SETTING.
Hydom Series “S” hydraulic operators are factory configured with double blocking,
close valves A and/or B using a 4mm Allen (hexagonal) wrench. Both valves are located on the bottom side
Valve closed

Screw in up to the stop.
Valve open

Once screwed in to the limit, unscrew
LINEAL «S» SERIES ACTUATORS. SPEED ADJUSTMENT.
Hydom Series “S” hydraulic operators are Factory set at high speed extension and retraction.
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side
Valve on the red screw side
Valve on the green screw side
Opening inwards
Open door
blocking
Open
Closed
WARNING: Excessive unscrewing can result in oil leaks and
can render the product useless.
WARNING: When unscrewing, avoid valves protruding from
the unit casing; risk of oil leaks and unit
ADJUST in quarter turn steps.
LINEAL «S» SERIES ACTUATORS. BLOCKING SETTING.
close valves A and/or B using a 4mm Allen (hexagonal) wrench. Both valves are located on the bottom side
Screw in up to the stop.
Once screwed in to the limit, unscrew
LINEAL «S» SERIES ACTUATORS. SPEED ADJUSTMENT.
Hydom Series “S” hydraulic operators are Factory set at high speed extension and retraction.
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side
Valve on the red screw side

Valve on the green screw side
Opening inwards
Open door
blocking
Closed door
blocking
Closed
Open
WARNING: Excessive unscrewing can result in oil leaks and
can render the product useless.
WARNING: When unscrewing, avoid valves protruding from
the unit casing; risk of oil leaks and unit
ADJUST in quarter turn steps.
close valves A and/or B using a 4mm Allen (hexagonal) wrench. Both valves are located on the bottom side
Screw in up to the stop.
Once screwed in to the limit, unscrew
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side

Adjust speed during retraction.
Valve on the green screw side

Adjust speed during extension.
Closed door
blocking
Open door
blocking
Closed
Open
WARNING: Excessive unscrewing can result in oil leaks and
can render the product useless.
WARNING: When unscrewing, avoid valves protruding from
the unit casing; risk of oil leaks and unit
ADJUST in quarter turn steps.
close valves A and/or B using a 4mm Allen (hexagonal) wrench. Both valves are located on the bottom side
Once screwed in to the limit, unscrew
one and a half turns.
To adjust (slow) the speed use a 2.5mm Allen (hexagonal) wrench to screw in the golden restrictor valves located on the side
s of the unit (see
Adjust speed during retraction.
Adjust speed during extension.
Opening outwards
Open door
blocking
Closed
Open
WARNING: Excessive unscrewing can result in oil leaks and
WARNING: When unscrewing, avoid valves protruding from
the unit casing; risk of oil leaks and unit
damage.
close valves A and/or B using a 4mm Allen (hexagonal) wrench. Both valves are located on the bottom side
one and a half turns.
s of the unit (see
Adjust speed during retraction.
Adjust speed during extension.
Opening outwards
Closed door
blocking
Open
Closed
WARNING: Excessive unscrewing can result in oil leaks and
WARNING: When unscrewing, avoid valves protruding from
damage.
close valves A and/or B using a 4mm Allen (hexagonal) wrench. Both valves are located on the bottom side
s of the unit (see
Closed door