Hyster E45-70XN User Manual

USER INTERFACE
SERVICE TECHNICIAN
E4.0-5.5XN, E5.0XNS
(E80-120XN, E100XNS) [A099];
A1.3-1.5XNT (A25-30XNT) [D203];
J1.5-2.0XNT (J30-40XNT) [K160];
E2.2-3.5XN (E45-70XN) [A268];
E1.6-2.0XN (E30-40XN) [A269];
J2.2-3.5XN (J45-70XN) [A276];
J1.6-2.0XN (J30-40XN) [A935];
J4.0-5.0XN (J80-100XN) [A970]
PART NO. 1688879 2200 SRM 1336

Hyster E45-70XN Specifications

General

Model	E45-70XN
Category	Forklifts
Power Source	Electric
Voltage	36V or 48V
Load Capacity	4500-7000 lbs (2041-3175 kg)
Lift Height	Up to 240 inches
Tire Type	Pneumatic
Weight	9, 000 - 12, 000 lbs
Travel Speed	up to 20 km/h

Summary

SAFETY PRECAUTIONS MAINTENANCE AND REPAIR

Menu Navigation

Operating Screen

PERFORMANCE MODE CONTROLS

Details how to control the four available performance modes.

STATUS AND WARNING ICONS

Describes status and warning indicators displayed on the screen.

Password Screen

Service Technician Password Setup

How technicians set up initial supervisor and other passwords.

ADDING/REMOVING/CHANGING PASSWORDS

Process for managing user passwords via Truck Setup menu.

Calibration Menu

LOAD WEIGHT CALIBRATION

How to calibrate the Load Weight Display.

RETURN TO SET TILT STOP POINT CALIBRATION

How to calibrate the Return to Set Tilt Stop Point.

E-HYDRAULIC AND MANUAL VALVE THRESHOLD CALIBRATION

Calibrating E-Hydraulic and manual hydraulic control valves.

STEERING WHEEL KNOB CENTER POINT CALIBRATION

Calibrating the steering wheel knob center point.

STEER AXLE POSITION CALIBRATION

Calibrating the steer axle position.

MANUAL HYDRAULICS CALIBRATION

Display Menu

Status Menu

Truck Setup Menu

Add/Remove Password

Allows technicians/supervisors to manage user passwords.

Motor Braking

Settings for motor braking: Regenerative, Auto Deceleration Rate/Type.

MOTOR BRAKING

Details motor braking settings: Regenerative and Auto Deceleration.

BATTERY SETUP

Configuring battery voltage, amp hour, and cell voltage settings.

BDI ADJUSTMENT SETTING

ACCELERATION RATES

Setting acceleration rates and performance modes.

HOUR METER INITIALIZATION

IMPACT MONITOR SHUTDOWN

Adjusting system reaction after an impact is detected.

OPERATOR CHECKLIST

MINIMUM PUMP STANDBY FLOW RATE

SCHEDULED MAINTENANCE REMINDER

Setting maintenance reminders based on time or hours.

Impact Detection

Setting Adjustments

Adjusting impact force and time settings.

Initial Adjustment of Soft and Hard Impact Settings

Initial setup for impact sensor settings.

MOTION ALARM

LIFT HYDRAULIC FUNCTION MAXIMUM SPEED AND RAMP TIMES

Lift function speed and ramp time settings.

LOWER HYDRAULIC FUNCTION MAXIMUM SPEED AND RAMP TIMES

Lower function speed and ramp time settings.

TILT FORWARD HYDRAULIC FUNCTION MAXIMUM SPEED AND RAMP TIMES

Tilt forward hydraulic function speed and ramp time settings.

TILT BACKWARD HYDRAULIC FUNCTION MAXIMUM SPEED AND RAMP TIMES

Tilt backward hydraulic function speed and ramp time settings.

AUXILIARY 1A HYDRAULIC FUNCTION MAXIMUM SPEED AND RAMP TIMES

Auxiliary 1A hydraulic function speed and ramp time settings.

AUXILIARY 1B HYDRAULIC FUNCTION MAXIMUM SPEED AND RAMP TIMES

Auxiliary 1B hydraulic function speed and ramp time settings.

AUXILIARY 2A HYDRAULIC FUNCTION MAXIMUM SPEED AND RAMP TIMES

Auxiliary 2A hydraulic function speed and ramp time settings.

AUXILIARY 2B HYDRAULIC FUNCTION MAXIMUM SPEED AND RAMP TIMES

Auxiliary 2B hydraulic function speed and ramp time settings.

OPTIONAL HYDRAULIC FUNCTIONS

Diagnostics Menu

RESTORE DEFAULT SETTINGS

FAULT CODE LOG

Viewing the 20 most recent fault codes for various devices.

TRACTION MOTOR 1 STATUS

TRACTION MOTOR 2 STATUS

BRAKE SYSTEM SENSORS

PUMP STATUS

HYDRAULIC CONTROL INPUTS

E-HYDRAULIC VALVES

HYDRAULIC SENSORS

SYSTEM VOLTAGES

STEERING POSITION SENSORS