To Next PageTo Next PageWhat to do if HYTROL 190-LRC Accessories conveyor will not start?
If the HYTROL Accessories conveyor won't start or the motor quits frequently, it could be due to a motor overload. Check for overloading of the conveyor. Alternatively, the motor might be drawing too much current. In this case, check the heater or circuit breaker and replace it if necessary.
Why is my HYTROL 190-LRC Accessories motor overheating?
If the motor or reducer of your HYTROL Accessories is overheating, several factors could be responsible. First, the conveyor might be overloaded; in this case, check the conveyor's capacity and reduce the load to the recommended level. Insufficient voltage to the motor may also cause overheating, so have an electrician check and correct this. Also, check the lubricant level in the reducer and relubricate it according to the manufacturer's recommendations. Finally, if one or more V-belts are too tight, reposition the take-up sheaves further from the double groove sheave.
What to do if HYTROL Accessories belt slips?
If the belt on your HYTROL Accessories is slipping or won’t move but the drive is running, it could be due to several reasons. The conveyor may be overloaded, so check its capability and reduce the load if necessary. The belt might also be too loose, so reposition the take-up sheaves closer to the double groove sheave. Lastly, there might be too much pressure against the belt; in this case, loosen the spring tension on the pressure rollers.
Why do HYTROL Accessories drive chain and sprockets wear excessively?
If the drive chain and sprockets on your HYTROL Accessories are wearing excessively, it could be due to a lack of lubrication on the chain, causing it to stretch and creating improper chain-to-sprocket mesh. Replace the chain and sprockets and provide adequate lubrication. Note that if the problem reoccurs, a chain take-up may be required. Another reason could be that the sprockets are out of alignment, so align them. A loose chain may also be the reason, so tighten the chain.
General| Brand | HYTROL |
|---|---|
| Model | 190-LRC Series |
| Category | Accessories |
| Language | English |
Procedures for checking received conveyor units for damage and completeness upon arrival.
Guidance on contacting dealers and providing necessary information for ordering replacement parts.
Importance of heeding warning signs on equipment to prevent potential dangers.
Safety guidelines for installing conveyors, including guarding, position, and headroom.
Steps for determining product flow and attaching supports to conveyor sections correctly.
Instructions for mounting ceiling hangers to conveyor sections for overhead applications.
Steps for positioning conveyor sections, connecting V-belts, and ensuring squareness.
Detailed instructions for installing V-belts on Model ACC conveyors using double groove sheaves.
Steps for connecting V-belts, including drive chain disconnection and roller adjustments.
Safety measures for operating conveyors, covering trained personnel, clear areas, and proper use.
Procedures for starting up the conveyor, including pre-start checks and area warnings.
Safety rules for maintenance tasks, emphasizing qualified personnel and lockout/tagout.
Guidelines for lubricating the drive chain based on ambient temperature and operating conditions.
Step-by-step instructions for replacing V-belts on different conveyor models.
Procedures for checking and adjusting drive chain alignment and tension for proper operation.
Identifies common conveyor problems, their causes, and recommended solutions.
A general checklist for routine maintenance of conveyor components like motor, reducer, and chains.
Steps for connecting the drive chain for an external slave drive setup.
Detailed parts drawing and list for the 190-ACC conveyor model.
Detailed parts drawing and list for the 190-LRC 90° conveyor model.
Detailed parts drawing and list for the 190-LRC 60° conveyor model.
Detailed parts drawing and list for the 190-LRC 45° conveyor model.
Detailed parts drawing and list for the 190-LRC 30° conveyor model.
Detailed parts drawing and list for the 190-LRS 45° conveyor model.
Detailed parts drawing and list for the 190-LRS 30° conveyor model.
Detailed parts drawing and list for the 190-LRSS 45° conveyor model.
Detailed parts drawing and list for the 190-LRSS 30° conveyor model.
List and drawings for sub-assemblies and related parts.
Drawings and part numbers for sheave retainer assemblies.
Drawing and parts list for slave connection components.
