IBM FlashSystem 5010 User Manual

CAUTION: CAUTION regarding IBM provided VENDOR LIFT TOOL:
• Operation of LIFT TOOL by authorized personnel only
• LIFT TOOL intended for use to assist, lift, install, remove units (load) up into rack elevations. It
is not to be used loaded transporting over major ramps nor as a replacement for such
designated tools like pallet jacks, walkies, fork trucks and such related relocation practices.
When this is not practicable, specially trained persons or services must be used (for instance,
riggers or movers). Read and completely understand the contents of LIFT TOOL operator's
manual before using.
• Read and completely understand the contents of LIFT TOOL operator's manual before using.
Failure to read, understand, obey safety rules, and follow instructions may result in property
damage and/or personal injury. If there are questions, contact the vendor's service and
support. Local paper manual must remain with machine in provided storage sleeve area.
Latest revision manual available on vendor's website.
• Test verify stabilizer brake function before each use. Do not over-force moving or rolling the
LIFT TOOL with stabilizer brake engaged.
• Do not raise, lower or slide platform load shelf unless stabilizer (brake pedal jack) is fully
engaged. Keep stabilizer brake engaged when not in use or motion.
• Do not move LIFT TOOL while platform is raised, except for minor positioning.
• Do not exceed rated load capacity. See LOAD CAPACITY CHART regarding maximum loads at
center versus edge of extended platform.
• Only raise load if properly centered on platform. Do not place more than 200 lb (91 kg) on
edge of sliding platform shelf also considering the load's center of mass/gravity (CoG).
• Do not corner load the platform tilt riser accessory option. Secure platform riser tilt option to
main shelf in all four (4x) locations with provided hardware only, prior to use. Load objects are
designed to slide on/off smooth platforms without appreciable force, so take care not to push
or lean. Keep riser tilt option flat at all times except for nal minor adjustment when needed.
• Do not stand under overhanging load.
• Do not use on uneven surface, incline or decline (major ramps).
• Do not stack loads. (C048, part 1 of 2)
Safety and environmental notices
ix

IBM FlashSystem 5010 Specifications

General

Brand	IBM
Model	FlashSystem 5010
Category	Storage
Language	English

Summary

Compliance standards

Safety and environmental notices

General safety

General safety guidelines for servicing the system.

Handling static-sensitive devices

Procedures for handling static-sensitive devices to prevent damage.

Power and cabling information for NEBS (Network Equipment-Building System) GR-1089-CORE

Power and cabling requirements for NEBS compliant installations.

About this guide

Who should use this guide

Identifies the intended audience for this installation guide.

How to get information, help, and technical assistance

How to get help and technical assistance from IBM.

Chapter 1. System overview

System hardware

Description of the system hardware components.

System management

Explanation of system management features and configuration node.

Chapter 2. Environmental requirements

Safety notices

General safety information for all rack-mounted devices.

Temperature requirements

Ensures environment temperature and humidity meet system requirements.

Physical characteristics

Summarizes dimension and weight information for enclosures.

Chapter 3. Before you begin the installation

Reviewing your packing slip

Verifies shipment contents against the packing slip.

Identify the hardware components

Review and identify hardware components and port locations.

Verify environmental requirements

Verifying site environmental and electrical requirements.

Chapter 4. Installing the system hardware

Installing support rails for the system

Procedure to install support rails for enclosures.

Installing an 5U expansion enclosure

Steps for installing a 5U expansion enclosure.

Installing or replacing a drive

Procedure to install or replace a drive in a 5U expansion enclosure.

Installing or replacing a 5U expansion enclosure in a rack

Procedure to install or replace a 5U expansion enclosure in a rack.

Powering on the system

Procedure to power on the system and check its status.

Chapter 5. Configuring the system

Initializing the system by using the technician port

Procedure to initialize the system using the technician port.

Adding an expansion enclosure to an existing system

Steps to add an expansion enclosure to an existing system.

Appendix A. Accessibility features for the system

Accessibility features

Major accessibility features for the system.

Appendix B. Where to find the Statement of Limited Warranty

Notices

Electromagnetic compatibility notices

Statements regarding electromagnetic compatibility.

United States Federal Communications Commission (FCC) Notice

FCC compliance notice for the equipment.