EasyManuals Logo

IBM System/370 User Manual

IBM System/370
259 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #152 background imageLoading...
Page #152 background image
IPL
Procedure
VS1
Sources: GC38-1001
VS1
Release 2 System
Messages
GC38-0110 Operator's
Library
OSNS1
Reference
Shown
below are a few sample replies
to
system messages received during initialization.
For
complete
information consult System Messages. According
to
your
system control
program,
the
messages you receive may have different id's from
the
ones shown here.
Reply, using
the
id fitting
your
message.
To
start
IPl,
dial
or
enter
address
of
SYSRES volume
and
press
lOAD
button.
IEA706A SPECIFY VIRTUAL STORAGE SIZE
Press END key
or
reply r
0,
'u'
(for default);
or
reply r
0,
'ddddd'
where ddddd
is
the
number
of
K bytes for virtual storage.
IEA101A SPECIFY SYSTEM ANDIOR SET PARAMETERS FOR RELEASE
02.0
OSNSI
Press END key
or
reply r 0,
'u'
to
iildicate no change
in
parameters;
r
0,
'u,
l'
to
indicate system should use system generation
val
ues
for
all
parameters
and should
print
all lists;
r
O:prmĀ·:
to
cancel a parameter for this loading which was specified during system
IIIIneration;
r O:prm=val'
to
indicate
the
value
of
this parameter for this loading:
r
O:prmcval,l'
Ie
gpecify
the
value for
the
parameter and
to
request a list
of
all
modules;
r
O:date=yy.ddd,clock;hh.mm.ss'
to
reset date andlor local time;
r
O:data=yy.ddd,clock;hh.mm.ss,gmt'
to
change
date
andlor
GMT
clock. After YO'J
se~
the
clock, press TOO
ClK
ENABLE switch before pressing END key.
IEA135A SPECIFY SYS1.DUMP TAPE UNIT ADDRESS OR
NO
Press END key
or
reply r
O:no'
if a SYS1.DUMP data
set
will
not
be used;
or
r
O,'ddd'
where
ddd
is
the 2400/3400 series tapp
~vi~~
!c
be
:!~cd
fC'i
-::~c
~"I"S~
.~U:'o'ir
data
set.
'00
IEEBOID CHANGE PARTITIONS - REPLY YES/NO (,LlST)
(Ouotes
around
text
are optional from here on.)
Reply r O,no
to
indicate partitions are
not
to
be defined;
r a,Yes partitions are to be redefined;
r O,list
only
a list
of
partitions
is
wanted:
r O,yes.list partitions are
to
be redefined and a list
is
wanted.
'01
IEEl14A
SPECIFY SET PARAMETERS OR U
Reply r 1,u
for
no
set
parameters;
r
l,proc=
for
spacifying a proc;
r l,q=(.f)
for
formatting
th~
queue;
r l.spool=(chng,fJ
for
changing spool;
or
any
combination
of
these, DATE, CLOCK, and GMT are not vaiid at :his time.
'02
iFBOlOD ENTER 'IPL REASON, SUBSYSTEM ID'
or
'U'
Page 4-86

Other manuals for IBM System/370

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the IBM System/370 and is the answer not in the manual?

IBM System/370 Specifications

General IconGeneral
BrandIBM
ModelSystem/370
CategoryServer
LanguageEnglish

Related product manuals