IDEAL SPLIT-JAW 61-096 User Manual

1 2
#61-096
200A~
61-096
CAT. IV
600V~
VA
H
Lo ZI
Ω
AUTO SEL
AC
DC
HOLD
VOLTS: 0-750VAC
0-1000VDC
AMPS: 0-200AAC
OHMS: 0-2000
Continuity
Split-Jaw
Smart-Meter
™
Ω
COM
CAT. IV
600V
CAT. III
1000V
V-Ω
Split-Jaw™
Smart-Meter
Register your product and
access more information at
www.idealindustries.com
Read First: Safety
Information
Understand and follow operating
instructions carefully. Use the meter,
test leads and all accessories only
as specified in this manual;
otherwise, the protection provided
by the meter can be impaired.
WARNING
To avoid possible electric
shock, personal injury or death,
follow these guidelines:
• Donotuseifmeterappearsdamaged.Visuallyinspectthe
meter to ensure case and jaws are not cracked.
• Inspectandreplacetestleadsifinsulationisdamaged,
metal is exposed, or probes are cracked. Pay particular
attention to the insulation surrounding the connectors.
• Alwaysensurethemeter,testleadsandallaccessories
meet or exceed the measurement category required in the
workingenvironment.(i.e.CATrating)
• Notethatthemeasurementcategoryandvoltagerating
of combinations of the meter, the test leads, and the
accessories is the lowest of the individual components.
• Donotusemeterifitoperatesabnormallyasprotection
maybe impaired.
•
Donotuseduringelectricalstormsorinwetweather.
• Donotusearoundexplosivegas,dust,vapor,amperage
or in damp or wet environments.
•
Donotapplymorethantheratedvoltagetothemeter.
• Removethetestleadsfromtheinputjacksbefore
measuring current.
• Replacebatteryassoonasbatteryindicatorappears
to avoid false readings.
• Removethetestleadsfromthemeterpriortoremoving
battery cover.
• Donotusewithoutthebatteryandbatterycoverproperly
installed.
• Donotattempttorepairthisunitasithasnouser-
serviceable parts.
• Usetheproperterminals,functionsandrangeforyour
measurements.
•
Nevergroundyourselfwhentakingelectricalmeasurements.
• Connecttheblackcommonleadtogroundorneutral
before applying the red test lead to potential voltage.
Disconnecttheredtestleadfromthevoltagefirst.
• Whenusingtheprobes,keepfingersbehindtheguard
rings of the probe tips.
• Voltagesexceeding30VACor60VDCposeashock
hazard so use caution.
CAUTION
Toprotectyourself,think“SafetyFirst”:
• Complywithlocalandnationalsafetycodes.
• Useappropriatepersonalprotectiveequipmentsuchas
face shields, insulating gloves, insulating boots, and/or
insulating mats.
• Beforeeachuse:
 - Performacontinuitytestbytouchingthetestleads
together to verify the functionality of the battery and
test leads.
 - Usethe3PointSafetyMethod.(1)Verifymeter
  operationbymeasuringaknownvoltage.(2)Apply
  metertocircuitundertest.(3)Returntotheknown
live voltage again to ensure proper operation.
• Alwaysworkwithapartner.
~
...
Symbols on the Unit
RiskofDanger.ImportantInformation.See
Manual.
Hazardous voltage.
Applicationaroundandremovalfrom
Hazardous Live conductors is permitted.
AC(AlternatingCurrent)
DC(DirectCurrent)
Earth Ground
CAT II
MeasurementCategoryIIappliestotest
and measuring circuits connected directly
to utilization points (socket outlets and
similarpoints)ofthelow-voltageMAINS
installation
CAT III
MeasurementCategoryIIIappliestomea-
suring circuits connected to the distribution
partofthebuilding’slow-voltageMAINS
installation
CAT IV
MeasurementCategoryIVappliestotest
and measuring circuits connected at the
sourceofthebuilding’slow-voltageMAINS
installation

IDEAL SPLIT-JAW 61-096 Specifications

General

Category	Measuring Instruments
Model	61-096
Brand	IDEAL
Type	Clamp Meter
Current Measurement	Yes
Voltage Measurement	Yes
Resistance Measurement	Yes
Continuity Test	Yes
Display	Digital
Battery Type	AAA
AC Current Range	0-400A

Summary

Safety Information and Precautions

General Safety Guidelines

Key safety guidelines and precautions for using the meter, including inspection and lead checks.

Important Cautions

Essential cautions to protect against hazards and ensure safe operation of the meter.

Unit Symbols

Explanation of symbols used on the meter unit for clarity and understanding.

Instrument Operation

Power On and Off

Procedures for turning the meter on and off, including the auto power off function.

Voltage Measurement

Instructions for measuring AC and DC voltages, including range and input impedance.

Resistance Measurement

Steps for measuring resistance and continuity, including range and open circuit voltage.

Advanced Functions

Continuity Test

Procedure for performing a continuity test and understanding its range.

AC Current Measurement

How to measure AC current using the jaw, including range and barrier information.

Data Hold Function

Instructions on using the data hold feature and understanding priority of function.

Battery Replacement

Guide for replacing the meter's battery.

Specifications and Warranty

General Specifications

Details on jaw opening, display, measuring rate, power, and environmental conditions.

Electrical Specifications

Technical data for voltage and current measurements, including accuracy and overload protection.

Resistance and Continuity Specs

Specifications for resistance and continuity functions, including ranges and accuracy.

Warranty Statement

Information on the product warranty, limitations, and legal rights.