IDEC FC4A-C10R2 - Page 520

viii « FC4A MICROSMART USER’S MANUAL »
INDEX
partial program download 5-28
password 5-26
PCD 28-26
Periphery_OK 28-24
permanent
configuration data (PCD)
28-26
parameter (PP) 28-27
phase
A
5-6, 5-8
B 5-6, 5-8
Z 5-6, 5-8, 5-15
Phoenix 3-18
PI 28-27
PID
control
21-2
instruction 21-1
notes for using 21-18
source operand S4 24-3
pinout 17-3, 17-32, 27-1, 30-4, 30-5, 30-6
RS232C connector 26-5
PLC status 5-26, 5-29, 7-13, 25-11, 29-1, 29-2
monitoring 26-3
point write 7-8, 7-10, 7-13
potentiometers analog 5-30
power
failure
29-4
memory protection 7-9
supply 2-3, 2-13, 3-16, 28-7
AS-Interface 28-3
sensor 2-5
voltage 3-16, 3-17
wiring 3-16, 3-17, 28-7
PP 28-27
precautions for
downloading high-speed counter program
5-10
programming ANST macro 24-21
preparation for using modem 27-9
preset
data registers
5-44
range 5-42
values
change counter
7-10
change timer 7-8
changing 7-13
restoring 7-13
process variable before conversion 21-13
processing time 28-18
profile 28-26
analog slave 28-21
program branching
instructions
18-1
using with SOTU/SOTD instructions 18-2
using with timer instruction 18-2
programming
catch input using WindLDR
5-18
clock cartridge accuracy using WindLDR 15-7
computer link using WindLDR 26-2
data link using WindLDR 25-7
data registers and internal relays 27-9
DI or EI using WindLDR 18-7
expansion data register using WindLDR 5-42
high-speed counter using WindLDR 5-11, 5-12
input filter using WindLDR 5-24
interrupt input using WindLDR 5-20
modem mode using WindLDR 27-10
partial program download using WindLDR 5-28
RXD instruction using WindLDR 17-24
special data register 17-32
timer interrupt using WindLDR 5-22
TXD instruction using WindLDR 17-12
user communication using WindLDR 17-5
user program protection using WindLDR 5-25
WindLDR 24-2
prohibited
instructions
29-22
ladder programs 29-22
protected mode 28-15
protection
circuit for output
3-15
type of 2-55
user program 5-25
PULS1 20-1
PULS2 20-1
pulse
input
5-6, 5-8, 7-18
instructions 20-1
output 2-15, 20-1
width modulation 20-7
pushbutton operation 28-14
pushbuttons and LED indicators 28-14
PWM1 20-7
PWM2 20-7
Q qty of
bytes
7-1, 8-1, 30-3
steps 30-3
quantities of slaves and I/O points 28-5
quantity of expansion I/O modules D8037 6-17
quit WindLDR 4-8
R RAMP 20-13
ramp control 20-13
read protect 5-25
reading
error data
29-1
time digital switch data 16-3
receive 17-15
completion output 17-15, 17-23
data byte count 17-24
digits 17-17
format 17-15, 17-16
instruction cancel flag M8022/M8023 17-24
slave data 28-35, 28-36
status 17-15, 17-23
code 17-23
timeout 17-5, 17-19, 17-23, 26-2
refresh
mode
25-9
time 25-10
relay output specifications
CPU module
2-7, 2-18
mixed I/O module 2-41
output module 2-31
removing
clock cartridge
2-67