IDEC FC4A-C24R2 User Manual

2: MODULE SPECIFICATIONS
2-16 « FC4A MICROSMART USER’S MANUAL »
DC Input Specifications (Slim Type CPU Module)
CPU Module
FC4A-D20K3
FC4A-D20S3
FC4A-D20RK1
FC4A-D20RS1
FC4A-D40K3
FC4A-D40S3
Input Points and Common Lines
12 points
in 1 common line
12 points
in 1 common line
24 points
in 2 common lines
Terminal Arrangement See CPU Module Terminal Arrangement on pages 2-19 through 2-22.
Rated Input Voltage 24V DC sink/source input signal
Input Voltage Range 20.4 to 26.4V DC
Rated Input Current
I0, I1, I6, I7: 5 mA/point (24V DC)
I2 to I5, I10 to I27: 7 mA/point (24V DC)
Input Impedance
I0, I1, I6, I7: 5.7 kΩ
I2 to I5, I10 to I27: 3.4 kΩ
Turn ON Time
I0 to I7: 35 µs + filter value
I10 to I27: 40 µs + filter value
Turn OFF Time
I0, I1, I6, I7: 45 µs + filter value
I2 to I5, I10 to I27: 150 µs + filter value
Isolation
Between input terminals: Not isolated
Internal circuit: Photocoupler isolated
Input Type Type 1 (IEC 61131)
External Load for I/O Interconnection Not needed
Signal Determination Method Static
Effect of Improper Input Connection
Both sinking and sourcing input signals can be connected. If any input
exceeding the rated value is applied, permanent damage may be caused.
Cable Length 3m (9.84 ft.) in compliance with electromagnetic immunity
Connector on Mother Board
FL26A2MA
(Oki Electric Cable)
MC1.5/13-G-3.81BK
(Phoenix Contact)
FL26A2MA
(Oki Electric Cable)
Connector Insertion/Removal Durability 100 times minimum
Input
O
perat
i
ng Range
The input operating range of the Type 1
(IEC 61131-2) input module is shown
below:
Transition
OFF Area
Input Voltage (V DC)
26.4
15
5
0
1.2 12.4
Input Current (mA)
ON Area
Area
11.36.5
24
Inputs I0, I1, I6, and I7
Inputs I2 to I5 and I10 to I27
Transition
OFF Area
Input Voltage (V DC)
26.4
15
5
0
1.2 7.7
Input Current (mA)
ON Area
Area
74.2
24
Input Internal
Ci
rcu
i
t
Input
Internal Circuit
COM
3.3 kΩ
Input
Internal Circuit
COM
4.7 kΩ
Inputs I0, I1, I6, and I7 Inputs I2 to I5 and I10 to I27
I/O Usage Limits
When using the FC4A-D20K3/S3 at an ambient temperature of 55°C in the
normal mounting direction, limit the inputs and outputs, respectively, which
turn on simultaneously along line (1).
When using the FC4A-D40K3/S3, limit the inputs and outputs, respectively,
which turn on simultaneously on each connector along line (2).
Input Voltage (V DC)
26.4
0
100
I/O Simultaneous ON Ratio (%)
24.0
(3) 40°C
50
(2) 55°C
(1) 55°C
60 70 800
When using at 40°C, all I/Os can
be turned on simultaneously at
26.4V DC as indicated with line (3).
When using the FC4A-D20RK1/
RS1, all I/Os can be turned on
simultaneously at 55°C, input volt-
age 26.4V DC.

IDEC FC4A-C24R2 Specifications

General

Brand	IDEC
Model	FC4A-C24R2
Category	Controller
Language	English