To Next PageTo Next PageWhy is my InFocus Projector remote control not working?
If the remote control for your InFocus Projector isn't working, start by replacing the batteries. If that doesn't work, ensure the ID numbers set in the projector and remote control match by pressing the ID button with the same ID number as the projector.
How to fix InFocus IN5132 Projector images when they are out of focus?
If the images from your InFocus Projector are out of focus or not well-superimposed, use the ZOOM, FOCUS, and LENS SHIFT features to fine-tune the superimposed images. If necessary, adjust PERFECT FIT and KEYSTONE as well.
How to fix InFocus IN5132 Projector when it does not turn on?
If your InFocus Projector isn't turning on, first, ensure the power cord is properly connected. If there was a power interruption, disconnect the power plug, let the projector cool for at least 10 minutes, and then try turning it on again. Also, make sure the lamp and lamp cover are securely attached, allowing the projector to cool for 45 minutes before checking.
Why my InFocus IN5132 Main and Sub projector do not operate in synchronization?
If the Main and Sub projectors aren't synchronizing, the RS-232 cable connecting them might be the issue. Ensure the RS-232 cable is properly connected and then restart the Main projector.
What to do if InFocus IN5132 Projector images do not superimpose properly?
If the images from the two projectors do not superimpose properly even after finely adjusting the image, try the following steps: 1. Press the AUTO button on the remote control or execute AUTO ADJUST EXECUTE on each of the projectors. 2. Adjust H POSITION and V POSITION on each of the projectors. 3. Check the RESOLUTION setting in the INPUT menu, and change the setting to match if the setting differs between Main and Sub.
Why do pictures appear dark on my InFocus IN5132?
If your InFocus Projector displays a dark picture, increase the BRIGHTNESS and/or CONTRAST in the menu. If it's in Eco mode, set ECO MODE to NORMAL and AUTO ECO MODE to OFF in the SETUP menu. If the lamp is old, consider replacing it.
What to do if the lens shutter is closed on InFocus IN5132?
Check the SHUTTER indicator on your InFocus Projector. If it's blinking, press the SHUTTER button on the control.
How to fix sound when it does not come out of InFocus Projector?
If the sound isn't coming out of your InFocus Projector, first, adjust the volume to a higher level using the menu or remote. Then, check that the AUDIO SOURCE/SPEAKER settings are correctly configured in the AUDIO menu. If using HDMI, verify that the selected HDMI AUDIO mode is appropriate for your device. Also, if you have selected USB TYPE A, turn the sound on from the Thumbnail menu. If you have selected USB TYPE B, remove the checkmark from the Sound checkbox in the Options window of 'LiveViewer Lite for USB'. If you have selected LAN, remove the checkmark from the Sound checkbox in the Option menu of LiveViewer.
What to do if my InFocus IN5132 Projector has no sound or picture?
If your InFocus Projector is producing no sound or pictures, check that the signal cables are correctly connected and that the input changeover settings are correct. Ensure that the AV MUTE function is not enabled by pressing the AV MUTE button on the remote. If using USB TYPE B, ensure it is set to USB DISPLAY in the OPTION menu, or select a different port for picture input.
What to do if InFocus Projector does not respond to the remote control?
If your InFocus Projector isn't responding to the remote control while using Intelligent Stack, it's likely because only the Main projector can receive remote control signals. Make sure to point the remote control directly at the Main projector.
Overview of projector features, part identification, and initial setup procedures.
Guidelines for projector placement, connecting devices, and power supply.
Instructions for remote control usage, battery installation, and power management.
How to adjust volume, aspect ratio, lens settings, and image parameters.
Selecting input signals, using display features, and correcting image distortion.
Procedures for replacing the lamp and cleaning the air filter.
Guidance on interpreting warnings, indicators, and resolving common issues.
Detailed technical data including dimensions, power consumption, and performance.
Legal terms governing the use and distribution of the projector software.
General
