InFocus IN5132c - User Manual

Other manuals for InFocus IN5132c

Manual De Usuario167 pages

Panduan Pengguna46 pages

Bedienungsanleitung45 pages

Questions and Answers

P
patricia47Sep 8, 2025
Why is my InFocus Projector remote control not working?
- T
  Theresa WilsonSep 8, 2025
  If the remote control for your InFocus Projector isn't working, start by replacing the batteries. If that doesn't work, ensure the ID numbers set in the projector and remote control match by pressing the ID button with the same ID number as the projector.
B
briananewmanAug 23, 2025
How to fix InFocus Projector images when they are out of focus?
- M
  Matthew GarzaAug 23, 2025
  If the images from your InFocus Projector are out of focus or not well-superimposed, use the ZOOM, FOCUS, and LENS SHIFT features to fine-tune the superimposed images. If necessary, adjust PERFECT FIT and KEYSTONE as well.
S
Scott JonesAug 25, 2025
How to fix InFocus IN5132c when it does not turn on?
- J
  jameswellsAug 26, 2025
  If your InFocus Projector isn't turning on, first, ensure the power cord is properly connected. If there was a power interruption, disconnect the power plug, let the projector cool for at least 10 minutes, and then try turning it on again. Also, make sure the lamp and lamp cover are securely attached, allowing the projector to cool for 45 minutes before checking.
H
hickmancoreyAug 26, 2025
Why my InFocus IN5132c Projector Main and Sub projector do not operate in synchronization?
- R
  rodriguezsusanAug 27, 2025
  If the Main and Sub projectors aren't synchronizing, the RS-232 cable connecting them might be the issue. Ensure the RS-232 cable is properly connected and then restart the Main projector.
T
Tracie EvansAug 27, 2025
What to do if InFocus Projector images do not superimpose properly?
- R
  Reginald OlsonAug 27, 2025
  If the images from the two projectors do not superimpose properly even after finely adjusting the image, try the following steps: 1. Press the AUTO button on the remote control or execute AUTO ADJUST EXECUTE on each of the projectors. 2. Adjust H POSITION and V POSITION on each of the projectors. 3. Check the RESOLUTION setting in the INPUT menu, and change the setting to match if the setting differs between Main and Sub.
O
Olivia ColemanSep 23, 2025
Why is the network not working on my InFocus Projector?
- J
  Jennifer KingSep 23, 2025
  If the network isn't working on your InFocus Projector, set STANDBY MODE to NORMAL in the SETUP menu. Also, ensure that different network addresses are set for both wireless and wired LAN.
E
Erik CaldwellSep 16, 2025
Why is the sound or image unstable on my InFocus IN5132c?
- B
  betty33Sep 16, 2025
  If the sound or image from your InFocus Projector is unstable or intermittent when LAN, USB TYPE A, or USB TYPE B is selected, it may be due to signal processing delay. Try changing the signal or using another port.
N
Nathan RamirezSep 18, 2025
Why is RS-232 not working on my InFocus IN5132c Projector?
- D
  Daniel MaxwellSep 18, 2025
  If RS-232 isn't working on your InFocus Projector, set STANDBY MODE to NORMAL in the SETUP menu. Also, ensure the COMMUNICATION TYPE for the CONTROL port is set to OFF in the OPTION - SERVICE - COMMUNICATION menu.
A
Angela CookSep 7, 2025
What to do if my InFocus IN5132c Projector has no sound or picture?
- P
  Phillip SmithSep 7, 2025
  If your InFocus Projector is producing no sound or pictures, check that the signal cables are correctly connected and that the input changeover settings are correct. Ensure that the AV MUTE function is not enabled by pressing the AV MUTE button on the remote. If using USB TYPE B, ensure it is set to USB DISPLAY in the OPTION menu, or select a different port for picture input.
G
Gina JonesSep 4, 2025
What to do if InFocus Projector does not respond to the remote control?
- K
  Kelly CarpenterSep 4, 2025
  If your InFocus Projector isn't responding to the remote control while using Intelligent Stack, it's likely because only the Main projector can receive remote control signals. Make sure to point the remote control directly at the Main projector.

InFocus IN5132c Specifications

General

Display Technology	DLP
Video Compatibility	NTSC, PAL, SECAM, HDTV (720p, 1080i, 1080p)
Projection Technology	DLP
Connectivity	HDMI, VGA, USB
Projection Size	30" - 300"
Native Resolution	1024 x 768
Keystone Correction	± 40° Vertical