Inovance Monarch 220-NICE-L-C-4018 User Manual

368 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Suzhou Inovance Technology Co., Ltd.

Add.: No. 16 Youxiang Road, Yuexi Town, Wuzhong District, Suzhou 215104, P.R. China

Tel: +86-512-6637 6666

Fax: +86-512-6285 6720

Service Hotline: 400-777-1260

http: //www.inovance.com

Shenzhen Inovance Technology Co., Ltd.

Add.: Building E, Hongwei Industry Park, Liuxian Road, Baocheng No. 70 Zone, Bao’an District, Shenzhen

Tel: +86-755-2979 9595

Fax: +86-755-2961 9897

Service Hotline: 400-777-1260

http: //www.inovance.com

User Guide

A01

Data code 19010735

NICE3000

new

Series Integrated Elevator Controller Advanced User Guide

Copyright 　 Shenzhen Inovance Technology Co., Ltd.

Integrated Elevator Controller

Advanced User Guide

NICE3000

new

Series

Table of Contents

Other manuals for Inovance Monarch 220-NICE-L-C-4018

User Guide152 pages

Questions and Answers:

S
Stephanie HarrisAug 27, 2025
What causes undervoltage in Inovance Monarch 220-NICE-L-C-4018 Controller?
- L
  Lee BakerAug 27, 2025
  Undervoltage in your Inovance Controller can be caused by a few things. It could be due to an instantaneous power failure on the input power supply, so check whether the power fails during running and ensure the wiring of all power input cables is secure. The input voltage might also be too low, so check the external power voltage. In some cases, the drive control board might be failing.
K
Kristina KennedySep 4, 2025
What should I do if my Inovance Monarch 220-NICE-L-C-4018 Controller reports a power supply phase loss?
- T
  Tanner JacksonSep 4, 2025
  If your Inovance Controller reports a power supply phase loss, it indicates that the power input phases are not symmetric. First, check whether any phase of the three-phase power supply is lost. Then, verify whether the three phases of the power supply are balanced. Also, check whether the power voltage is normal, and adjust the power voltage if necessary. For 220 V models, you can set FC-01 bit 14 to 1 to cancel detection of this fault.
C
Casey TaylorSep 7, 2025
What are the common causes of motor auto-tuning faults in Inovance Monarch 220-NICE-L-C-4018?
- K
  kdavisSep 7, 2025
  A motor auto-tuning fault in your Inovance Controller can occur for various reasons: * If learning the stator resistance fails, check whether the motor wiring is correct. * If learning the magnetic pole position fails. * If the synchronous motor static auto-tuning mode is selected, but the encoder is not SIN/COS, select another auto-tuning mode or use a SIN/ COS encoder. * If CD signal fluctuation is large in synchronous motor static auto-tuning, hardware interference exists. Check whether grounding is correct. * If Leaning the encoder zero- position angle fails in synchronous motor angle-free auto- tuning, obtain the encoder zero-point angle in inspection state, and then perform half- automatic angle-free auto-tuning under normal-speed running.
L
louisharrellSep 8, 2025
What should I check if my Inovance Monarch 220-NICE-L-C-4018 Controller indicates a power output phase loss?
- G
  Gregory GarciaSep 8, 2025
  If your Inovance Controller indicates a power output phase loss, the issue likely stems from the output wiring of the main circuit being loose. Check whether the motor wiring is secure and verify whether the RUN contactor on the output side is normal.
K
Kristopher CharlesSep 10, 2025
How to troubleshoot a RUN contactor feedback abnormal error on an Inovance Controller?
- B
  Brian BowenSep 12, 2025
  A RUN contactor feedback abnormal error on your Inovance Controller can have a couple of causes: * If the feedback of the RUN contactor is active, but the contactor has no output, check whether the feedback contact of the contactor acts properly and check the signal feature (NO, NC) of the feedback contact. * If the current of the asynchronous motor from acceleration to constant-speed running is too small (? 0.1 A), check whether the output cables UVW of the controller are connected properly and check whether the control circuit of the RUN contactor coil is normal.
J
Justin JuarezSep 12, 2025
What causes the 'door lock disconnected during running' error in Inovance Monarch 220-NICE-L-C-4018 Controller?
- E
  Eric LaraSep 12, 2025
  If your Inovance Controller displays a 'door lock disconnected during running' error, indicated by subcodes 101 or 102, it means the door lock circuit feedback is invalid during elevator operation. Check whether the hall door lock and the car door lock are in good contact. Also, verify whether the door lock contactor acts properly, check the signal feature (NO, NC) of the feedback contact on the door lock contactor, and ensure the external power supply is normal.
M
Matthew FlemingSep 13, 2025
Why is my Inovance Monarch 220-NICE-L-C-4018 Controller showing a safety circuit disconnected error?
- B
  brendaharveySep 13, 2025
  If your Inovance Controller is showing a safety circuit disconnected error (Subcode 101), it means the safety circuit signal has become off. Check the safety circuit switches and their states. Also, verify whether the external power supply is normal, ensure the safety circuit contactor acts properly, and confirm the signal feature (NO, NC) of the feedback contact of the safety circuit contactor.
A
Allen StaffordSep 14, 2025
What to do when the Inovance Monarch 220-NICE-L-C-4018 Controller shows 'Maintenance notification period reached'?
- B
  Benjamin HernandezSep 14, 2025
  If your Inovance Controller displays 'Maintenance notification period reached', it means the elevator hasn't been maintained within the notification period. Power-off and maintain the elevator or disable the maintenance notification function by setting F9-13 to 0.

Inovance Monarch 220-NICE-L-C-4018 Specifications

General

Brand	Inovance
Model	Monarch 220-NICE-L-C-4018
Category	Controller
Language	English

Related product manuals

Monarch 220-NICE-L-C-4011

Monarch 220-NICE-L-C-4015

Monarch 220-NICE-L-C-4007

Monarch 220-NICE-L-C-4022

Monarch 220-NICE-L-C-4030

Monarch 220-NICE-L-C-4022F

Monarch 220-NICE-L-C-4030F

Inovance Monarch NICE-L-C-2003

Inovance Monarch NICE-L-C-4003

Inovance Monarch NICE-L-C-4030F

Preview: Monarch NICE300new Series

Monarch NICE300new Series

Preview: Monarch NICE 3000 new Series

Monarch NICE 3000 new Series