This appliance is not intended for use by persons
(including children) with reduced physical sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
DO NOT operate without factory-recommended
safety guards.
DO NOT put your hands into the disposer while it is
in operation.
Switch off or unplug the appliance before attempting
to free a jammed rotor with an implement.
• DO NOT put any of the following items into the
disposer: clam or oyster shells, drain cleaner, glass,
china, plastic wrap, large bones, metal objects,
explosive materials, extremely hot water, grease, oil,
or syrup.
• DO NOT overload disposer with excess amounts of
food waste and water. The unit will consume food
waste faster when you feed it steadily.
• DO NOT touch the water valve after the correct flow
of water is achieved by adjusting plumbing valves.
Grinding efficiency will be decreased if the water
swirl is more than 1/2 way up the disposer body.
• DO NOT stop disposer with food waste in it; let it
run for approximately three (3) minutes to clear itself
of all ground waste. This will help maintain a clean
and odor-free unit and avoid drainline stoppage.
If the disposer stops suddenly it may be
due to overloading or a foreign object
(metal) has caused a jam condition.
Turn control to off position and complete
following steps:
1. Insert dejamming wrench (not
supplied) slot down through sink
opening. Place slot over raised bars
found on top of rotating shredder.
2. Twist dejamming wrench back and
forth to free jam. Rotating shredder
should revolve freely when jam is
released.
3. Remove all foreign materials.
4. Allow disposer to cool for 3-5 minutes
after it stops running. Press red reset
button to reset overload protector.
Never strike reset button with objects.
5. If disposer remains inoperative after
following these steps, contact nearest
InSinkErator Factory Authorized
Service Center.
Call
1-800-845-8345 to find
Service Center nearest you.
IMPORTANT SAFETY INSTRUCTIONS
RELEASING DISPOSER JAM
VOLTAGE/PHASE AVAILABILITY
Model Voltage, Hz Phase
SS100-28 115/208/230V 1Ph
SSC100 -1 115/208/230V 1Ph
SS100-35 100/200/230V, 50/60Hz 1Ph
SS100-47 208/230/460V, 60Hz 3Ph
SSC100-3 208/230/460V, 60Hz 3Ph
SS100-50 208-230/460/3 3Ph
SS200-27 115/208/230V 1Ph
SS200-31 115/208/230V 1Ph
SSC200-1 115/208/230V 1Ph
SS200-35 208/230/460V, 60Hz 3Ph
SS200-36 208/230/460V, 60Hz 3Ph
SS200-39 380/50-60Hz 3Ph
SSC200-3 208/230/460V, 60Hz 3Ph
SS300-21 415 V 3Ph
SS300-22 220 V 3Ph
SS300-23 380V, 50/60Hz 3Ph
SS300-25 208/230/460V, 60Hz 3Ph
Model Voltage, Hz Phase
SS300-27 208/230/460V 3Ph
SS500-22 230/460V 3Ph
SS500-23 415V 3Ph
SS500-27 380V 3Ph
SS500-28 208/230/460V, 60Hz 3Ph
SS500-30 208/230/460V 3Ph
SSC500-1 208/230/460V 3Ph
SS1000-10 208/230/460V, 60Hz 3Ph
SS1000-12 208/230/460V 3Ph
To Previous Page
Loading...
