Why does the overload protector trip frequently on my InSinkErator SS-50 Garbage Disposal?
The overload protector of your InSinkErator Garbage Disposal might be tripping frequently because the disposer is overloaded with food waste. Avoid overloading the disposer with excessive amounts of food waste.
How to fix continuous water flow in InSinkErator SS-50?
If the water flows continuously before the controls are turned on for your InSinkErator Garbage Disposal, reinstall the water solenoid valve with the arrow on the valve pointing in the direction of the water flow.
What to do if my InSinkErator SS-50 will not start and water does not run?
If your InSinkErator garbage disposal won't start and water isn't running either, here are a couple of things to check: * There may be no power to the disposer. Replace the switch or repair the control center. Also, check for blown fuses or a tripped circuit breaker. * The disposer control switch may not be connected or could be faulty. Connect or repair/replace the control switch.
What to do if InSinkErator SS-50 Garbage Disposal motor stops while grinding?
If your InSinkErator Garbage Disposal motor stops while grinding, but water continues to flow, it could be due to a jam or a tripped overload protector. First, turn the control to the off position and press the red reset button on the disposer. If the disposer was running, allow the unit to cool for 3-5 minutes before pressing the red reset button. Never strike the reset button with an object. For a jam, insert a dejamming bar (not supplied) slot down through the sink opening. Place the slot over one end of the raised bars found on the top of the rotating shredder. Using an adjustable wrench or a pipe wrench for leverage, twist the dejamming bar back and forth to free the jam. The rotating shredder should revolve freely when the jam is released. Remove all foreign material that caused the ...
What to do if InSinkErator SS-50 Garbage Disposal won't start but water flows?
If your InSinkErator Garbage Disposal won't start but water flows, it could be because the overload protector has tripped or the disposer is jammed. Turn the control to the off position and press the red reset button on the disposer. To address a jam, turn the control to the off position and complete the following steps: 1. Insert a dejamming bar (not supplied) slot down through the sink opening, placing the slot over one end of the raised bars on top of the rotating shredder. 2. Use an adjustable wrench or pipe wrench for leverage to twist the dejamming bar back and forth to free the jam. The rotating shredder should revolve freely once released. 3. Remove any foreign material causing the stoppage. 4. Allow the disposer to cool for 3-5 minutes after it stops running, then press the r...
What to do if my InSinkErator SS-50 Garbage Disposal will not start but water runs?
If your InSinkErator garbage disposal won't start but the water is running, here are a few things to check: * The overload protector may have tripped. Allow it to cool for 5 minutes, then reset it. * The overload protector may be burned out. In this case, test and replace it. * The stator might be burned out. Test the stator and inspect for pinched stator lead wires. * The rotating shredder could be jammed. Turn the control to the OFF position and insert the dejamming bar (slot down) through the sink opening. Place the slot over one end of the raised bars found on the top of the rotating shredder. Twist the dejamming bar back and forth to free the jam. Remove any foreign matter, allow the disposer to cool for 3-5 minutes, and press the red reset button. * There may be water in ...
How to fix InSinkErator Garbage Disposal motor that hums but does not run?
If your InSinkErator garbage disposal motor hums but doesn't run, and water is running, consider the following: * The rotating shredder may be jammed, or the stator/lower end frame/upper end bell misaligned. See previous “Jammed rotating shredder” solution. Remove and realign sections. Ensure thru bolts are not bent or broken. Replace bolts if necessary. * The rotor shaft might be binding against the stator core. Check for score marks and replace the stator or rotor shaft if necessary. Check for worn bearings and replace if needed. * The start switch may be inoperative (1 Phase only). Replace the start switch. * The stator windings may be open. Test the stator windings and replace the stator if open. Check for water leaks and repair as necessary. * The capacitor charge might be ...
Highlights potential hazards and safety precautions to prevent injury or death.
Describes the data found on the unit's specification decal for identification purposes.
Provides detailed charts of physical dimensions for various models and installation considerations.
Outlines the essential steps for safely disconnecting and removing the disposer unit from its installation.
Details the procedure for replacing the gasket within the grinding chamber to ensure proper sealing.
Covers the testing and replacement process for the unit's overload protection device.
Details testing and installation procedures for the capacitor on single-phase units.
Provides instructions for testing stator windings for continuity, shorts, or grounds.
General| Brand | InSinkErator |
|---|---|
| Model | SS-50 |
| Category | Garbage Disposal |
| Language | English |
To Next Page
