Need help?Do you have a question about the Interacoustics Eclipse EP15 and is the answer not in the manual?
General| Channels | 2 |
|---|---|
| Storage Temperature | -20°C to 60°C |
| Humidity | 10% to 90% non-condensing |
| Output Levels | -10 dB HL to 120 dB HL |
| Transducers | Insert earphones, Headphones, Bone vibrator |
| Test Types | ABR, ASSR, ECochG |
| Connectivity | USB |
| Stimuli | Tone burst, Chirp, Click |
| Display | External display required |
| Operating Temperature | 15°C to 35°C |
Provides information about the manual and its validity.
Details the intended use cases for the Eclipse system and its modules.
Specifies the qualified personnel authorized to operate the Eclipse system.
Defines the target patient demographics for the Eclipse system and its modules.
Lists conditions and patient factors that contraindicate testing with the Eclipse system.
Describes the Eclipse system, its capabilities, and included parts.
Explains the meaning of warning, caution, and notice labels used in the manual.
Provides important safety and usage precautions for the Eclipse device.
Guides users on how to unpack and inspect the Eclipse instrument for damage.
Explains the various symbols and markings found on the Eclipse instrument.
Provides instructions and warnings for connecting the Eclipse to mains and computer.
Details how to connect the Eclipse's ground plug to the patient bed for noise reduction.
Identifies and explains the functions of the ports on the Eclipse back panel.
Lists requirements and notices before starting the Eclipse software installation.
Specifies the hardware and operating system requirements for the Eclipse software.
Lists the necessary software, hardware, and cables for installing the Eclipse.
Provides step-by-step instructions for installing the Eclipse module software.
Guides on how to install the necessary driver for the Eclipse hardware.
Explains how to restore factory defaults and install language packs.
Describes the functionality of the Eclipse software when operating as a reader station.
Explains how to access serial numbers and license keys within the software.
Provides instructions on how to launch the Eclipse software from OtoAccess .
Guides on configuring Eclipse modules within OtoAccess if icons are missing.
Guides on launching the Eclipse software modules from Noah 4.
Highlights safety and preparation steps before performing EP tests with Eclipse.
Details the File, Edit, and View menus for system setup, printing, and display options.
Explains help, protocol selection, and reporting functions within the Record tab.
Details how to display A-B curves, contra curves, and single curves.
Covers saving sessions, stimulus rate selection, and display gain.
Explains stimulus parameters, manual stimulation, status, and waveform reproducibility.
Details the Start/Stop, Pause, and Next Intensity controls for measurements.
Explains Fmp/noise graphs, extending sweeps, raw EEG, and advanced EEG analysis.
Covers hiding artifacts, adjusting display gain, and selecting waveforms.
Details moving curves, displaying differential curves, and adding notes.
Guides on placing, deleting, and suggesting waveform markers.
Details hiding, fixating curves for comparison, and merging curves.
Explains adding curves and displaying differential Ipsi-Contra curves.
Covers changing filtering, viewing recorded conditions, and adding comments.
Explains cursor usage, SNR calculation, and waveform markers (CR, RA, INC).
Explains how to display latency and interlatency values for marked waveforms.
Describes the graphical presentation of latency changes relative to stimulus intensity.
Guides on disabling desktop composition in Windows 7 for optimal EPx5 performance.
Covers SN10 markers and troubleshooting help launch issues.
Lists keyboard shortcuts for accessing various functions within the Eclipse software.
Details pre-test procedures including patient information and electrode placement.
Guides on performing impedance checks and transducer placement.
Provides an overview of ABR threshold recording for individuals unable to participate in behavioral audiometry.
Details electrode montage and available stimuli for ABR threshold testing.
Guides on editing recorded ABR data and interpreting results for infant fitting.
Describes electrode montage and editing for neuro latency recordings.
Explains how latency and inter-latency calculations are indicated on the printout.
Covers eABR recording overview, electrode montages, and editing.
Details using eABR to estimate current levels for cochlear implant tuning.
Covers ECochG recording overview, electrode montages, and stimuli.
Shows examples of marked points for amplitude and area ratio in ECochG.
Covers CM recording overview, electrode montage, stimuli, and interpretation.
Covers AMLR recording overview, electrode montage, and available stimuli.
Shows an example of an AMLR threshold recording using Tone Burst.
Covers ALR recording overview, electrode montage, and stimuli.
Explains ALR interpretation and using correction factors for infant fitting.
Covers P300/MMN overview, montage, stimuli, and parameter summary.
Explains how to perform loop back testing using the LBK15 unit.
Highlights safety and preparation steps before performing VEMP tests.
Explains the automatic preamplifier adjustment and the VEMP monitor.
Details the available VEMP waveform markers (P1, N1, P1', N1') for analysis.
Guides on calculating the VEMP asymmetry ratio by setting VEMP partners.
Explains how to scale VEMP amplitudes based on pre-stimulus EMG.
Covers cVEMP overview, electrode montage, and typical stimuli.
Specifies default parameters, procedure, and editing for cVEMP results.
Shows an example of a cVEMP recording for a patient with a lowered threshold.
Covers oVEMP overview, electrode montage, and typical stimuli.
Specifies default parameters and procedure for oVEMP testing.
Guides on editing oVEMP results and shows an example.
Explains research module options for exporting curves and logging sweeps.
Guides on exporting averaged curves or full sessions for further analysis.
Guides on importing WAV files for stimuli and calibration.
Warns about potential IA OAE Suite crashes due to PC sleep/hibernation settings.
Lists devices compatible with IA OAE Suite and its functionality.
Provides instructions for launching IA OAE Suite from OtoAccess or Noah 4.
Explains how to enable simulation mode for practice without saving data.
Covers DPOAE module operation, test preparation, and results interpretation.
Describes menu, guidance, print, save, and toggle ear functions in the DPOAE screen.
Covers TEOAE module operation, probe testing, and environment requirements.
Describes menu, guidance, print, save, and toggle ear functions in the TEOAE screen.
Explains graph view options, zoom, and saving/exiting functionalities.
Details changing norm data display and viewing waveform buffers.
Guides on creating, selecting, and managing custom print templates.
Highlights ABRIS precautions and details electrode mounting procedures.
Guides on performing impedance checks and loop back testing for ABRIS.
Provides an overview of the ABRIS test screen elements.
Details ABRIS menu items, historic sessions, stimulus, and status windows.
Guides on starting, pausing, and managing ABRIS recordings.
Explains ABRIS status bar indicators and response curve monitoring.
Lists keyboard shortcuts for ABRIS operations.
Highlights ASSR precautions and patient preparation for reliable test results.
Details skin preparation, electrode placement, and impedance checks for ASSR.
Explains the use of LBK15 for functional testing of ASSR.
Provides an overview of the ASSR tab, including menu items and protocol selection.
Details ASSR menu, historic sessions, stimulus, and status windows.
Guides on starting, pausing, and managing ASSR recordings.
Explains the ASSR test frequency graph and interpretation of the ASSR table.
Guides on extending test time and adjusting stimulus intensity for ASSR.
Explains how to stop the current ongoing intensity for ASSR tests.
Explains the Audiogram tab for viewing estimated audiograms and correction factors.
Provides recommendations for care and maintenance to ensure instrument safety and performance.
Details recommended cleaning solutions and procedures for instruments and accessories.
Provides specific instructions for cleaning the OAE probe tip to ensure accurate measurements.
Outlines conditions for instrument repair and details warranty terms.
Lists technical details for the Eclipse hardware, including CE-mark, standards, and dimensions.
Provides technical specifications for the EP15, EP25, and VEMP modules.
Lists technical details for the TEOAE module, including probe specifications.
Lists technical details for the DPOAE module, including probe specifications.
Lists technical details for the ABRIS module, including stimulus and recording parameters.
Lists technical details for the ASSR module, including stimulus and transducer options.
Provides EMC information, precautions, and guidance for the Eclipse instrument.
Summarizes test types and functionality for EP15, EP25, and VEMP modules.
Details maximum stimulus intensity levels for various transducers used with EP modules.
Summarizes test types and functionality for the TEOAE module.
Summarizes test types and functionality for the DPOAE module.
Summarizes functionality for the ABRIS module, including stimulus and test parameters.
Summarizes functionality for the ASSR module, including stimulus and transducer options.
To Next Page