does not flash the control panel is not operational or the
databus is faulty (usually cabling).
TX: LED flashes to indicate the DGP is replying to polling from
the ATS control panel. If the RX LED flashes but the TX LED
does not, it indicates that the DGP is not programmed to be
polled in the control panel or that it is addressed incorrectly.
Zone numbering
Table 1: Zone and output numbering
Control panel 1–16 DGP8 129–144
DGP1 17–32 DGP9 145–160
DGP2 33–48 DGP10 161–176
DGP3 49–64 DGP11 177–192
DGP4 65–80 DGP12 193–208
DGP5 81–96 DGP13 209–224
DGP6 97–112 DGP14 225–240
DGP7 113–128 DGP15 241–256
ATS1210(L)E and ATS1211E have eight zones on-board.
ATS1210LE can be equipped with ATS1202 eight-zone
expansion module that expands zone number to 16.
There are 16 zones allocated to every DGP address. If zones 9
to 16 are not available, they should be programmed as type 0
(zone disabled) in the Zone database.
Output numbering
See Table 1 above.
A DGP can have a maximum of 16 outputs available as relays
or open collector outputs. The output numbers are the same as
the 16 zone numbers allocated to the DGP address.
The output numbers can be used if output controllers are
connected to the DGP that corresponds to those output
numbers.
Examples:
• DGP1 has 8 zones: 17 to 24
• DGP1 outputs (max 16): 17 to 32
Programming
The programming map is shown in Figure 5.
See Advisor Master Programming Guide for more details on
the DGP programming.
Extended mode
To enable anti-mask detection it is necessary to select
Extended mode. Standard mode is needed for backwards
compatibility. Default is Extended mode.
Technical specifications
Supply voltage 10.5 to 13.8 V (12 V nom.)
Current consumption 53 mA max.
Data retention > 40 years
Dimensions (H x W) (size BB board) 90 x 80 mm
Housing dimension (H x W x L):
ATS1643 small metal housing
ATS1644 small plastic housing
ATS1647 large plastic housing
165 x 125 x 36mm
86 x 125 x 36 mm
120 x 240 x 38 mm
Weight
ATS1211E
ATS1210E
ATS1210LE
790 g
190 g
390 g
Operating temperature −10 to +55°C
IP rating IP30
Relative humidity < 95%, noncondensing.
Regulatory information
Manufacturer UTC Fire & Security Americas Corporation, Inc. 1275
Red Fox Rd., Arden Hills, MN 55112-6943, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Certification
EN 50131-1 System requirements
EN 50131-3 Control and indicating equipment
Security Grade 3, Environmental class II
Tested and certified by Telefication B.V.
European
Union
directives
1999/5/EC (R&TTE directive): Hereby, UTC Fire &
Security declares that this device is in compliance with
the essential requirements and other relevant
provisions of Directive 1999/5/EC.
2002/96/EC (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
Contact information
www.utcfireandsecurity.com or www.interlogix.com.
For customer support, see www.interlogix.com/customer-
supp
ort.
DE: Installations Beschreibung
Anwendungsbereich
ATS1210(L)E und ATS1211E sind abgesetzte Erweiterungen
mit 8 MG für das Advisor Master System.
Montage der Erweiterung
Die Platine kann in jedem vorhandenen Gehäuse der ATS-
Serie montiert werden, welches das BB-Format unterstützt.
Die AME kann auch in einem der nachfolgenden separaten
Gehäuse montiert werden: ATS1644 (Kunststoff), ATS1647
(Kunststoffgehäuse, groß) und dem ATS1643 (Metall). Die
Gehäuse mit Montagelöchern (Position 1) sind in den
Abbildungen 2 bis 4 dargestellt. Position 2 und 3 zeigen
die Montagelöcher für den Sabotage-Abreißkontakt.
Alle Abmessungen sind in mm angegeben.
P/N 1077869 • REV 1.0 • ISS 31OCT11 3 / 16
To Next Page
Loading...