Interlogix ATS1340 User Manual

© 2019 UTC Fire & Security Americas Corporation, Inc. 1 / 12 P/N 1056702 (ML) • REV E • ISS 06MAR19
ATS1340 Door Junction Box Installation Sheet
EN
DE
FI
IT
1
2
EN: Installation Sheet
Description
The ATS1340 is designed as a universal door junction box.
The module has an incoming and outgoing data bus / power
connection to achieve a proper stub connection for an Advisor
Master bus reader.
Onboard relays are provided to connect a door lock and
auxiliary outputs (i.e. buzzer). For high-energy locks an
external 12 V or 24 V power supply must be connected.
Two onboard dual loop resistor inputs configurations are
prepared to connect a magnetic switch on the door and the
switch in the door lock if necessary. These connections can be
easily hardwired to the nearest DGP or panel zones.
The Advisor Master bus reader can be fully wired to the door
junction box and a request to the exit button easily can be
connected as well. For more details of the door application
please see Figure 2.
WARNING: Disconnect the mains power before opening the
cabinet! Disconnect AC mains plug from AC mains wall socket,
or disconnect the mains with the dedicated circuit breaker.
Disconnect the battery (when applicable).
Description of ATS1340 and door
application
Figures 1 and 2
(1) From auxiliary output
(2) 12 V/24 V ext. power supply
(3) Databus IN from panel or
DGP
(4) Databus OUT to RAS / DGP
(5) Auxiliary relay output (RL3)
(6) Auxiliary OC output
(7) Shield
(8) To Smart Card reader
(9) RTE button
(10) Door lock relay output (RL1)
(11) From door switches
(12) From external tamper
(13) To zone inputs
Mounting location
The ATS1340 PCB (see Figure 1) can be mounted in any
Advisor Master cabinet, which supports the size B board.
Preferably the door junction box must be mounted in close
proximity to a door, which needs access control and / or alarm
facilities.
J1
J9
J6
J2
J3
J8J12
F1
F2
J4
RL3
RL1
J15
J16
J13
J14
D4
D5
D+
D-
+12V
0V
CWG
CWG
0V
12/24V
OC OUT
SPARE
C
W
G
C
W
G
0
V
+
1
2
V
D
-
D
+
0
V
(+
)
+ O
C
C
W
G
C
W
G
Zn+1 Zn EXTERN TAMPER MAGN SW. ON DOOR
SW. IN DOOR
LOCK 12/24V FOR DOOR LOCK +EXIT
-BUTTON
D+
D
-
+12V
0V
EXIT/B.LED
BUZ.
R/B LED
(1)
(2)
(3)
(4) (5) (6) (7)
(8)
(9)(10)(11)(12)(13)
ATS1340
J18
J17
RL3
RL1
NO NC
NO NC
ATS1340
(1)
(2)
(3)
(5)(6)
(11)
(4)
(8)(9)(10)

Interlogix ATS1340 Specifications

General

Brand	Interlogix
Model	ATS1340
Category	Network Hardware
Language	English

Summary

ATS1340 Door Junction Box Installation Sheet

Product Description

The ATS1340 is designed as a universal door junction box with incoming/outgoing data bus connections for Advisor Master bus readers.

Door Application Overview

Details the ATS1340's role in door access control, including connections for door locks, auxiliary outputs, and magnetic switches.

Mounting Location

Recommends mounting the ATS1340 PCB near doors requiring access control or alarm facilities.

Safety Precautions

Mandates disconnecting mains power and battery before opening the cabinet to prevent electrical hazards.

Mounting the Unit

Wall or Ceiling Mounting

Step-by-step instructions for securely mounting the ATS1340 junction box to a surface, including tamper switch installation.

Connecting the ATS1340

Databus In Wiring

Connects incoming BUS cable wires to terminal strip J1 on the ATS1340 for panel or DGP communication.

Databus Out Wiring

Connects outgoing BUS cable wires to terminal strip J12 for linking to the next bus device.

Smart Card Reader Connections

Details wiring for connecting an Advisor Master reader to terminal strip J9, including LED and buzzer signals.

Door Lock and Exit Button Connections

Explains how to connect a door lock and request-to-exit button to terminal strip J6.

Door Switch Wiring

Guides on connecting magnetic switches for the door and door lock to terminal strip J4.

Zone and Tamper Connections

Details connecting Advisor Master/DGP inputs and external tamper to terminals J3.

External Power Supply and OC Input

Describes connecting external 12/24V DC power to J2 and OC input to J3.

Auxiliary Output Wiring

Details wiring for auxiliary output (RL3) and OC output via terminal strip J8.

Jumper Configuration

Explains jumper settings for zone functionality (J13, J14), N/O or N/C output (J18), and power supply selection (J16).

Specifications

Regulatory Information

Contact Information