Interlogix xGenConnect NXG-216N - Page 77

176 pages

To Next Page

To Previous Page

xGenConnect Installation and Programming Guide 65

reported to OH. If the fault remains present for a longer period, the LAN fault

message will be reported after 180 seconds.

Main Page

Table of Contents5
Important Information9
Limitation of Liability9
Product Warnings9
Warranty Disclaimers10
Disclaimer11
Intended Use11
Advisory Messages12
Introduction13
System Capacity13
Xgenconnect Specifications14
Product Codes14
Mains Power Specifications15
Installation Instructions for Service Persons15
Power Supply Specifications15
General Features16
Current Consumption18
Output Current Rating18
Auxiliary Current and Battery Capacity19
Environmental19
Physical Dimensions and Weight19
Fuses20
Maintenance20
System Monitoring21
SIA and CID Reporting Code Descriptions21
50131-3 and en 50136-2 Compliancy25
Options Affected by en 50131 Regulations25
Optional Functions26
50131 Compliance Precautions26
Alarm Transmission Path and Alarm Transmission System Faults27
50131 And INCERT Certified Components27
Other Regulations28
E) Wiring Diagram29
E) Terminals31
E) Leds32
Wiring Diagram33
Terminals33
Leds33
Wiring Diagram34
Terminals34
Leds34
Detector EOL Wiring35
Power Requirements35
Cable Requirements35
Grounding35
Shielding36
Termination Links36
Installing Panel37
Installing Legacy NX Modules38
Installing Antennas38
Plastic Enclosure40
Xgen Metal Enclosure41
Enrolling Modules41
Deleting Modules42
Arming and Disarming Your System44
Keypress Tamper44
Lock out on 3 Invalid Attempts44
Arm Your System with NXG-1820-EUR Keypad44
Arm Your System with NXG-183X Keypad45
Disarm Partitions with NXG-1820-EUR Keypad46
Disarm Partitions with NXG-183X-EUR Keypad46
Activate SOS Feature (NXG-1820-EUR Only)46
Programming Methods48
Account Access48
Method 1: DLX900 Management Software49
Method 2: Web Server51
Method 3: Ultrasync+ App54
Method 4: NXG-1820 Keypad60
Programming with Web Pages61
Recommended Items to Change61
Learning Wireless Zones62
Adding a User67
Adding a Keyfob68
Advanced Keyfob Programming68
Programming Cameras70
Configuring Email Reports75
Configuring OH Reports75
Enabling Push Notifications on Smartphone78
Enable SMS Notification (Future Release)83
Z-Wave Home Automation Hub (Future Release)85
Adding Z-Wave Devices85
Programming Z-Wave Siren86
Removing Z-Wave Devices87
Adding Xgenconnect to Existing Z-Wave Network as Secondary Controller88
Removing Xgenconnect from Existing Z-Wave Network as Secondary Controller89
Adding Xgenconnect to Existing Z-Wave Network as Primary Controller90
Relinquish Primary Control of Xgenconnect to Another Controller91
Creating a Device Association93
Replacing a Failed Node94
Creating a Device Association94
Removing a Failed Node94
Rediscover Z-Wave Nodes95
Backup Z-Wave Network96
Reset Z-Wave Network96
Restore Z-Wave Network96
Send User Pins to Z-Wave Door Lock97
Programming Scenes99
Xgenconnect with Amazon Alexa103
Xgenconnect Works with Google Assistant105
Programming Instructions110
Programming Instructions for System Options110
Programming Instructions for Permissions114
Programming Instructions for Menus116
Programming Instructions for Holidays118
Programming Instructions for Users121
Programming Instructions for Zones124
Programming Instructions for Custom Zones127
Programming Instructions for Areas130
Programming Instructions for Schedules133
Programming Instructions for Arm-Disarm137
Programming Instructions for Communicator142
Programming Instructions for Ultrasync145
Programming Instructions for Event Lists147
Programming Instructions for Channels149
Programming Instructions for Zone Reporting153
Programming Instructions for System Event Reporting155
Programming Instructions for Actions157
Programming Instructions for Action Groups159
Programming Instructions for Scenes161
Programming Instructions for Outputs162
Combining Actions with Schedules163
Walk Test163
User Reporting164

Interlogix xGenConnect NXG-216N - Page 77

Table of Contents

Related product manuals