Intex 28636 User Manual

83 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

108A

(108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/06/2016

English

108A

English

OWNER’S MANUAL

IMPORTANT

SAFETY RULES

Please read, understand, and follow all

instructions carefully before installing

and using this product. Keep for future

reference.

Don’t forget to try these other fine Intex products: pools,

pool accessories, inflatable pools and in-home toys, airbeds

and boats available at fine retailers or visit our website.

Due to a policy of continuous product improvement, Intex reserves

the right to change specifications and appearance, which may

result in updates to the instruction manual without notice.

For illustrative purposes only.

©2016 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.- Intex

Recreation Corp.

All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte

vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.

®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/

Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in

Lizenz von/

Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex

Recreation Corp., P.O. Box 1440, Long Beach, CA 90801

• Distributed in the European Union by/Distribué dans l’Union Européenne

par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/

Intex Trading B.V., Venneveld 9, 4705 RR

Roosendaal – The Netherlands

www.intexcorp.com

Krystal Clear™

Model 636T Filter Pump

220 - 240 V~, 50 Hz, 165 W

Hmax 1.0 m, Hmin 0.19 m, IPX5

Max. Water Temperature 35 °C

108-*A*-R0-1706

Table of Contents

Questions and Answers:

D
David GarciaAug 5, 2025
Why won't my Intex Water Pump filter motor start?
- A
  Anna DixonAug 5, 2025
  If your Intex Water Pump filter motor won't start, several factors could be at play. First, ensure the filter cord is securely plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the GFCI/RCD circuit breaker has tripped, reset it. If it repeatedly trips, there may be an electrical defect, so turn off the breaker and consult an electrician. Lastly, the motor might be too hot, causing the overload protection to shut off; in this case, allow the motor to cool down.
S
stephen40Aug 10, 2025
What to do if my Intex 28636 doesn't pump water or the water flow is very slow?
- M
  Michael RoblesAug 10, 2025
  If your Intex Water Pump isn't pumping water effectively or the water flow is very slow, start by checking for clogged inlets or discharges and clear any obstructions in the intake hose. Ensure there are no air leaks on the intake line by tightening hose nuts and inspecting hoses for damage, also verify the pool water level. Replace the cartridge if there's scale or buildup. For an excessively dirty pool, clean the cartridge more often. Also, ensure you clean inside the plunger valve. Verify that the nozzle and strainer connection are properly oriented by pulling the valve handle to the full upright position and install the nozzle at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet.
K
Karina GregoryAug 14, 2025
What should I check if my Intex 28636 Water Pump doesn't work?
- R
  randy31Aug 14, 2025
  If your Intex Water Pump isn't working, start by checking the water level and fill the pool to the correct level. Clean the strainer screens at the pool inlet, as they might be plugged up. Inspect the intake hose for air leaks, tightening hose nuts and checking for damage. Clear any sticks or leaves in the intake hose, as a faulty motor or jammed impeller could be the cause. Lastly, address any air lock inside the cartridge chamber by turning and pulling the valve handle to the full upright position.
B
Brandon ReeseAug 19, 2025
How to fix a leaking hose on my Intex 28636 Water Pump?
- J
  joycetateAug 19, 2025
  If your Intex Water Pump hose is leaking, first ensure that the hose nuts are well-fitted by tightening or reinstalling them. Check if the hose o-ring dislodged when connecting the hose and put the o-ring back into the groove. If the hose is broken, replace it with a new one.
D
Dean CarrilloAug 22, 2025
What to do if the air jet valve is leaking on my Intex Water Pump?
- D
  Donna BrownAug 22, 2025
  If the inlet threaded air connector or air jet valve on your Intex Water Pump is leaking, ensure the plunger valve is well-fitted by tightening or reinstalling it. Make sure the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON and run for a few seconds, then turn it OFF, repeating this process three times. If the internal seal is dirty, remove the air jet valve, flush out any dirt with water, and replace the valve. If the air jet valve is broken, replace it with a new one.
R
Rachel WestAug 27, 2025
How to stop the top cover from leaking on my Intex 28636?
- K
  kristi79Aug 27, 2025
  If the top cover of your Intex Water Pump is leaking, first remove the cover and check for a missing O-ring. Also, ensure that the cover or air release valve is tight by manually tightening them.
L
Lisa KramerAug 31, 2025
How do I resolve an air lock in my Intex Water Pump?
- B
  Bradley SellersAug 31, 2025
  If you have an air lock in your Intex Water Pump, it means there’s air trapped in the pump housing and inlet hose. To resolve this, open the air release valve and wait until water starts to flow out of the valve, then close it. Also, ensure that the inlet and outlet hoses are connected correctly, with the lower position of the pool outlet connected to the filter pump water inlet and the upper position of the pool inlet connected to the filter pump water outlet.

Intex 28636 Specifications

General

Model	28636
Hose diameter	1.25 inches
Power	99 W
Type	Water Pump
Pump's water flow rate	2006 l/h
Suitable for pool volume	Up to 3000 gallons
Power Source	Electric
Weight	4.7 kg

Summary

Important Safety Rules

Parts Reference

Pool Outlet Strainer and Plunger Valve Setup

Pool Inlet Nozzle and Plunger Valve Setup

Filter Pump Hose Connection Setup

Filter Pump Stationary Mounting Option

Operating Instructions

Timer Mode Operation

Guide on setting the timer dial and operating the filter pump for automatic cycles.

Manual Mode Operation

Instructions for manually turning the filter pump on and off for filtration.

Operating Time Table

Cleaning or Replacing Filter Cartridges

Pool Care and Chemicals

Long Term Storage & Winterization

Troubleshooting Guide

Common Pool Problems

General Aquatic Safety

Limited Warranty

Related product manuals

Preview: Intex SF80220-2

Intex SF80220-2

Intex ECO 20110

Intex SF70220-2

Intex SF60220-2

Preview: Intex ECO15230-2

Intex ECO15230-2

Intex ECO15220-2

Intex ECO20220-2

Intex ECO20230-2

Intex PureSpa SSP-H-10-2

Preview: Intex Krystal Clear SF90220-2

Intex Krystal Clear SF90220-2

Preview: Intex Quick-Fill

Intex Quick-Fill

Preview: Intex Krystal Clear SX1500

Intex Krystal Clear SX1500