EasyManua.ls Logo

Intex ECO 20110 - User Manual

Intex ECO 20110
35 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
261
PO
(261PO) Sand Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 07/23/2014
English
Sand Filter Pump &
Saltwater System with E.C.O.
(Electrocatalytic Oxidation)
Model ECO 20110 & 15110
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves the
right to change specifications and appearance, which may result in
updates to the instruction manual without notice.
OWNER’S MANUAL
For illustrative purposes only.
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance, Visit
www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
261-*PO-R0-1507

Table of Contents

Questions and Answers

  • H
    hdavisAug 18, 2025
    What to do if my Intex ECO 20110 Water Pump filter doesn’t clean the pool?
    • C
      Craig MoralesAug 18, 2025
      If your Intex Water Pump filter isn't effectively cleaning the pool, consider the following: * Ensure proper chlorine and pH levels. Adjust as necessary. * Make sure there is filtering media in the tank; load with filter sand. * Verify the 6-way valve setting position is set to “FILTER”. * If the pool is excessively dirty, operate the filter for longer periods. * If there is dirt or sand on the pool floor, use an Intex pool vacuum to clean the bottom of the pool. * If the basket is restricting the water flow, clean the basket.
  • P
    Priscilla GilbertAug 21, 2025
    How to fix a leaking hose on my Intex ECO 20110 Water Pump?
    • L
      Lisa ColonAug 21, 2025
      To fix a leaking hose on your Intex Water Pump: * Ensure the hose nut is securely tightened or reinstall it. * Check that the hose connection fitting o-ring/L-shape o-ring is in place and undamaged.
  • J
    Joshua HillAug 25, 2025
    Why is the 6-way valve or cover leaking on my Intex Water Pump?
    • W
      wericksonAug 25, 2025
      If the 6-way valve or cover is leaking on your Intex Water Pump: * Remove the 6-way valve cover and ensure the o-ring is in place. * Clean the sand tank o-ring with garden hose water if it's dirty. * Tighten the flange clamp with the wrench supplied.
  • A
    Anthony MillsAug 28, 2025
    What does it mean if there are white flakes in the water when using Intex ECO 20110?
    • S
      Sydney TerrellAug 28, 2025
      If you observe white flakes in the water while using your Intex Water Pump, it indicates excessive calcium hardness. To address this, drain about 20 to 25% of the pool water and add fresh water to decrease the calcium hardness. Also, inspect the electrolytic cell for scale buildup and clean it if necessary.
  • W
    William FisherAug 31, 2025
    Why does my Intex ECO 20110 have insufficient chlorine?
    • C
      carriegreerAug 31, 2025
      If your Intex Water Pump shows insufficient chlorine, consider these factors: * Chlorine loss may be due to intense sunlight exposure. Use a pool cover when the pool is not in use or when the unit is operating. * If the bather load has increased, increase the daily Saltwater System operating time. * A clogged or dirty electrolytic cell can cause this issue. Remove the cell for inspection and clean it if necessary. * High UV level exposure may be the cause. Cover the pool with a pool cover for 2 days with the device running, then test the water using the test strips.
  • J
    Joseph PierceSep 3, 2025
    Why is sand flowing back into the pool from my Intex ECO 20110?
    • S
      smithsaraSep 3, 2025
      If sand is flowing back into the pool from your Intex Water Pump: * Ensure you are using only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75, as the sand may be too small. * The sand bed might be calcified; if so, change the sand.
  • M
    Micheal HarrisonSep 10, 2025
    What to do if there is no LED display on my Intex ECO 20110?
    • A
      Autumn ChandlerSep 12, 2025
      If there is no LED display on your Intex Water Pump: * Ensure the cell cord is firmly plugged into the cell housing receptacle, as there may be no power supply. * Reset the RCD/GFCI, as it may not have reset.
  • R
    Robin StephensonNov 13, 2025
    Why is my Intex ECO 20110 filter not pumping water or the flow is very slow?
    • C
      Chad CochranNov 13, 2025
      If your Intex Water Pump isn't pumping water or the flow is slow, consider these potential causes: * The inlet or discharge may be clogged. Clear any obstructions in the intake hose by discharging it inside the pool wall. * There might be an air leak on the intake line. Tighten hose nuts and check hoses for damage. Also, check the pool water level. * If the pool is excessively dirty, clean the pre-filtering basket more often. * The sand media could be clogged with dirt. Backwash the filter. * The nozzle and strainer connections might be reversed. Install the nozzle at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. * There might be crusting or caking on the filtering sand surface. Remove about 1” of sand if necessary. * A pool ...

Summary

Setup Instructions

Motor Pre-Filter Assembly Setup

Connects and prepares the motor and pre-filter housing.

Sand Tank Installation

Positions and secures the main sand filter tank.

Sand Loading Procedure

Guides filling the filter tank with the correct sand media.

6-Way Valve Installation

Attaches the multi-port valve to the filter tank assembly.

Saltwater System Operation Guide

Saltwater System Boost Cycle

Activates enhanced sanitization for immediate chlorine production.

Power Saving Stand-by Mode

Details the system's energy-saving sleep and stand-by functions.

Independent Pump Operation

Explains running the filter pump without the saltwater system.

Maintenance Procedures

Motor Pre-Filter Cleaning and Maintenance

Procedures for cleaning and maintaining the motor pre-filter.

Flow Sensor Cleaning

Steps to clean the flow sensor for accurate readings.

Intex ECO 20110 Specifications

General IconGeneral
ModelECO 20110
Voltage220-240 V
Frequency50 Hz
Pump's water flow2006 l/h
Filtration capacity2006 l/h
Discharge Outlet Size13 mm
Maximum Discharge Flow2000 LPH
Maximum Head1.2 m

Related product manuals