EasyManua.ls Logo

Intex ECO20110-1 - User Manual

Intex ECO20110-1
35 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
261
PO
(261PO) Sand Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/04/2018
English
Sand Filter Pump &
Saltwater System with E.C.O.
(Electrocatalytic Oxidation)
Model ECO20110-1 & 15110-1
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves the
right to change specifications and appearance, which may result in
updates to the instruction manual without notice.
OWNER’S MANUAL
For illustrative purposes only.
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance, Visit
www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
261-*PO-R0-1905

Table of Contents

Questions and Answers

  • K
    Kyle StevensAug 18, 2025
    What to do if my Intex Water Pump filter doesn't pump water or has very slow flow?
    • P
      Pamela PatrickAug 18, 2025
      If your Intex Water Pump filter doesn't pump water or the flow is very slow, start by clearing any obstructions in the intake hose. Next, check for air leaks on the intake line by tightening hose nuts and inspecting hoses for damage, also check the pool water level. If the pool is excessively dirty, clean the pre-filtering basket more often. Backwash the filter if the sand media is clogged with dirt. Ensure that the nozzle is at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. If the filtering sand surface has crusted, remove about 1” of sand if necessary. Remove any pool vacuuming device attached to the system line. Ensure the inlet threaded air connector is connected to the pool inlet upper hole.
  • A
    Anthony SheltonAug 20, 2025
    How to troubleshoot an Intex Water Pump filter motor that fails to start?
    • D
      dwhiteAug 20, 2025
      If the Intex Water Pump filter motor isn't starting, ensure the power cord is securely plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter (GFCI) or RCD. Also, check if the GFCI/RCD circuit breaker has tripped and reset it. If it repeatedly trips, consult an electrician. The motor may also be too hot, in which case, let it cool down before restarting. Finally, check if the pump is in stand-by/power saving mode.
  • M
    Michael BartlettAug 23, 2025
    Why isn't my Intex ECO20110-1 Water Pump filter cleaning the pool properly?
    • T
      Timothy SanchezAug 23, 2025
      If the Intex Water Pump filter isn’t cleaning the pool effectively, ensure the valve is set to the “FILTER” position. Clean the basket, operate the filter for longer periods if the pool is excessively dirty, and use an Intex pool vacuum to clean dirt or sand from the pool floor. For improper chlorine or pH levels, adjust them, and consult your local swimming pool supply stores. If there's no filtering media in the tank, load it with filter sand.
  • D
    Douglas GonzalesAug 28, 2025
    How can I fix insufficient chlorine levels with my Intex ECO20110-1 Water Pump?
    • J
      James LeonardAug 28, 2025
      If you have insufficient chlorine in your pool when using the Intex Water Pump, use a pool cover when the pool is not in use and/or when the unit is operating to avoid chlorine loss due to intense sunlight exposure. Increase the daily Saltwater System operating time if the bather load has increased or due to insufficient operating hours of the Saltwater System. Check the salt level with the Test Kit and adjust as needed if the salt level in the pool water is less than 2000ppm. Remove the cell for inspection, clean it if necessary if the electrolytic cell is clogged or dirty. Cover the pool with a pool cover for 2 days with the device running and then test the water using the test strips if there is a high UV level exposure.
  • J
    Jordan LeAug 31, 2025
    What causes the 6-way valve or cover to leak on my Intex ECO20110-1 and how to fix it?
    • K
      kathrynharperAug 31, 2025
      If the 6-way valve/cover is leaking on your Intex Water Pump, remove the 6-way valve cover and ensure the o-ring is in place. Clean the sand tank o-ring with garden hose water if it's dirty. Tighten the flange clamp securely if it's not tight.
  • R
    Richard PinedaSep 2, 2025
    Why is sand flowing back into the pool from my Intex ECO20110-1?
    • K
      Kevin MartinezSep 2, 2025
      If sand is flowing back into the pool from your Intex Water Pump, ensure that you are using only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Change the sand if the sand bed is calcified.
  • M
    mramosSep 4, 2025
    Why is the hose leaking on my Intex ECO20110-1 Water Pump?
    • R
      Robert BakerSep 4, 2025
      If a hose is leaking on your Intex Water Pump, tighten or reinstall the hose nut securely. Also, ensure the o-ring/L-shape o-ring is in place and not damaged at the hose connection fitting.
  • M
    martinsarahSep 7, 2025
    Why are there white flakes in the water when using my Intex ECO20110-1 Water Pump?
    • D
      daniel87Sep 7, 2025
      If you observe white flakes in the water while using your Intex Water Pump, drain about 20 to 25% of the pool water and add fresh water to decrease the calcium hardness. Inspect the electrolytic cell for scale buildup and clean it if necessary.
  • A
    Alyssa ClaySep 10, 2025
    What causes chronic low water level in a pool using an Intex ECO20110-1?
    • J
      jonesjoshuaSep 10, 2025
      If you're experiencing a chronic low water level in your pool, inspect the pool liner and hoses for any rips or holes and repair them with a patch kit. Ensure that all drain valve caps are finger-tight.
  • D
    David PooleSep 12, 2025
    How to remove sediment on the pool bottom with my Intex ECO20110-1?
    • K
      Kimberly NavarroSep 12, 2025
      If there's sediment on the pool bottom, use an Intex pool vacuum to clean it.

Summary

Important Safety Rules

Parts Reference

Setup Instructions

Pool Outlet - Strainer & Plunger Valve Setup (optional)

Instructions for installing the pool outlet strainer and plunger valve assembly.

Pool Inlet - Nozzle & Plunger Valve Setup (optional)

Instructions for installing the pool inlet nozzle and plunger valve assembly.

Motor Pre-Filter Assembly Setup

Steps for assembling the motor and pre-filter components.

Sand Tank Installation

Steps for correctly installing the sand filter tank and its base.

Sand Loading

Detailed instructions on how to load the correct type and amount of sand.

6-Way Valve Installation

Steps for connecting the 6-way valve to the filter tank and motor.

Product Specifications

How the Electrocatalytic Oxidation Works

Sand Filter Pump Hose Connection Setup

Operating Instructions

6-Way Valve Positions and Function

Explanation of the different 6-way valve settings and their functions.

Initial Startup and Operation

Steps for the initial setup and operation of the filter pump system.

Saltwater System Operation

Start Up the Unit

Procedure to plug in, test, and turn on the saltwater system.

Set Operating Hours for Saltwater System

Guide to setting the daily operating hours for the saltwater system.

Lock Keypad Controls

How to lock the control panel to prevent unauthorized changes.

Readjust Operating Time if Necessary

Instructions for changing the previously set operating hours.

Boost Cycle

How to activate the boost cycle for increased sanitizer production.

Stand-by;Power Saving Mode

Explanation of the system's power saving and stand-by modes.

Running the Pump Alone Without the Saltwater System

How to operate only the filter pump without the saltwater function.

LED Code Chart

Salt & Pool Water Volumes

Which Kind of Salt to Use

Guidance on selecting the appropriate type of salt for pool sanitation.

Optimum Salt Levels

Recommended salt concentration for optimal system performance.

Adding Salt

Step-by-step instructions for adding salt to the pool water.

Removing Salt

Procedure to lower salt concentration if it becomes too high.

Pool Volume Calculation

Formulas for calculating pool volume in gallons and cubic meters.

Intex Pools Salt Table

Intex Pools Cyanuric Acid Table

Intex Pools Operating Time Table (with Cyanuric Acid)

Salt Calculation Formula for All Pools

Salt Table for Common Non-Intex Pools

Cyanuric Acid Table for Common Non-Intex Pools

Operating Time Table for Common Non-Intex Pools

Motor Pre-Filter Cleaning and Maintenance

Flow Sensor Cleaning

Electrolytic Cell Cleaning

E.C.O. Electrode Cleaning

Maintenance (continued)

Intex Test Strips (Packed with the Product)

Instructions for using test strips to monitor pool water chemistry.

Pool Care & Chemicals

General advice on maintaining pool water clarity and hygiene with chemicals.

Pool Maintenance & Chemical Definitions

Long Term Storage & Winterization

Troubleshooting Guide

Common Pool Problems

General Aquatic Safety

Limited Warranty

Intex ECO20110-1 Specifications

General IconGeneral
BrandIntex
ModelECO20110-1
CategoryWater Pump
LanguageEnglish

Related product manuals