EasyManua.ls Logo

Intex ECO15110-1 - User Manual

Intex ECO15110-1
35 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
261
PO
(261PO) Sand Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/04/2018
English
Sand Filter Pump &
Saltwater System with E.C.O.
(Electrocatalytic Oxidation)
Model ECO20110-1 & 15110-1
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves the
right to change specifications and appearance, which may result in
updates to the instruction manual without notice.
OWNER’S MANUAL
For illustrative purposes only.
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance, Visit
www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
261-*PO-R0-1905

Table of Contents

Questions and Answers

  • T
    tthompsonAug 18, 2025
    What to do if my Intex ECO15110-1 Water Pump filter doesn't pump water or has very slow flow?
    • R
      Ryan HamptonAug 18, 2025
      If your Intex Water Pump filter doesn't pump water or the flow is very slow, start by clearing any obstructions in the intake hose. Next, check for air leaks on the intake line by tightening hose nuts and inspecting hoses for damage, also check the pool water level. If the pool is excessively dirty, clean the pre-filtering basket more often. Backwash the filter if the sand media is clogged with dirt. Ensure that the nozzle is at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. If the filtering sand surface has crusted, remove about 1” of sand if necessary. Remove any pool vacuuming device attached to the system line. Ensure the inlet threaded air connector is connected to the pool inlet upper hole.
  • T
    Thomas DavisAug 20, 2025
    How to troubleshoot an Intex ECO15110-1 filter motor that fails to start?
    • A
      Alexander HarmonAug 20, 2025
      If the Intex Water Pump filter motor isn't starting, ensure the power cord is securely plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter (GFCI) or RCD. Also, check if the GFCI/RCD circuit breaker has tripped and reset it. If it repeatedly trips, consult an electrician. The motor may also be too hot, in which case, let it cool down before restarting. Finally, check if the pump is in stand-by/power saving mode.
  • O
    oreynoldsAug 23, 2025
    Why isn't my Intex Water Pump filter cleaning the pool properly?
    • J
      Jim MooreAug 23, 2025
      If the Intex Water Pump filter isn’t cleaning the pool effectively, ensure the valve is set to the “FILTER” position. Clean the basket, operate the filter for longer periods if the pool is excessively dirty, and use an Intex pool vacuum to clean dirt or sand from the pool floor. For improper chlorine or pH levels, adjust them, and consult your local swimming pool supply stores. If there's no filtering media in the tank, load it with filter sand.
  • V
    Vickie GriffinAug 28, 2025
    How can I fix insufficient chlorine levels with my Intex ECO15110-1 Water Pump?
    • C
      Chelsea JonesAug 28, 2025
      If you have insufficient chlorine in your pool when using the Intex Water Pump, use a pool cover when the pool is not in use and/or when the unit is operating to avoid chlorine loss due to intense sunlight exposure. Increase the daily Saltwater System operating time if the bather load has increased or due to insufficient operating hours of the Saltwater System. Check the salt level with the Test Kit and adjust as needed if the salt level in the pool water is less than 2000ppm. Remove the cell for inspection, clean it if necessary if the electrolytic cell is clogged or dirty. Cover the pool with a pool cover for 2 days with the device running and then test the water using the test strips if there is a high UV level exposure.
  • P
    Patricia HoganAug 30, 2025
    What causes the 6-way valve or cover to leak on my Intex ECO15110-1 Water Pump and how to fix it?
    • A
      Anthony HowardAug 31, 2025
      If the 6-way valve/cover is leaking on your Intex Water Pump, remove the 6-way valve cover and ensure the o-ring is in place. Clean the sand tank o-ring with garden hose water if it's dirty. Tighten the flange clamp securely if it's not tight.
  • A
    amybartonSep 2, 2025
    Why is sand flowing back into the pool from my Intex ECO15110-1 Water Pump?
    • Z
      Zachary DavilaSep 2, 2025
      If sand is flowing back into the pool from your Intex Water Pump, ensure that you are using only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Change the sand if the sand bed is calcified.
  • J
    joshua08Sep 5, 2025
    Why is the hose leaking on my Intex Water Pump?
    • H
      Heather StanleySep 5, 2025
      If a hose is leaking on your Intex Water Pump, tighten or reinstall the hose nut securely. Also, ensure the o-ring/L-shape o-ring is in place and not damaged at the hose connection fitting.
  • J
    Joseph ClarkSep 7, 2025
    Why are there white flakes in the water when using my Intex ECO15110-1 Water Pump?
    • M
      Matthew JonesSep 7, 2025
      If you observe white flakes in the water while using your Intex Water Pump, drain about 20 to 25% of the pool water and add fresh water to decrease the calcium hardness. Inspect the electrolytic cell for scale buildup and clean it if necessary.
  • K
    kyleprattSep 10, 2025
    What causes chronic low water level in a pool using an Intex ECO15110-1 Water Pump?
    • K
      Kelly MyersSep 10, 2025
      If you're experiencing a chronic low water level in your pool, inspect the pool liner and hoses for any rips or holes and repair them with a patch kit. Ensure that all drain valve caps are finger-tight.
  • P
    Pamela Boyle PhDSep 12, 2025
    How to remove sediment on the pool bottom with my Intex ECO15110-1?
    • T
      tammy56Sep 12, 2025
      If there's sediment on the pool bottom, use an Intex pool vacuum to clean it.

Summary

Safety Information

Important Safety Rules

Essential safety precautions for operating the pump and saltwater system.

Detailed Safety Instructions

Comprehensive warnings and cautions for installation and use.

Product Details and Setup

Parts Identification and Reference

Visual guide and list of all system components.

Product Specifications

Technical data and performance metrics of the system.

Installation Guide

Step-by-step assembly, sand loading, and hose connection instructions.

System Operation and Monitoring

6-Way Valve and Filter Pump Operation

Understanding valve modes and basic pump functions.

Saltwater System Controls

Operating the E.C.O. saltwater generator, settings, and modes.

LED Codes and Alarms

Interpreting system indicators and error messages.

Pool Care and Maintenance

Water Chemistry Management

Guidance on salt, chemicals, and water testing.

Salt and Chemical Dosage Tables

Recommended amounts for various pool sizes.

Cleaning and Maintenance Procedures

Steps for cleaning filter components and electrodes.

Troubleshooting, Storage, and Warranty

Long Term Storage

Preparing the system for off-season storage.

Troubleshooting Guide

Identifying and resolving common operational issues and pool problems.

Limited Warranty

Details of the product's warranty coverage.

Intex ECO15110-1 Specifications

General IconGeneral
ModelECO15110-1
CategoryWater Pump
TypeSubmersible
Power SourceElectric
Frequency50 Hz
Suction Head8 m
Body MaterialPlastic
Cable Length10 m
Warranty1 Year
Voltage220-240V

Related product manuals