EasyManua.ls Logo

Intex Easy Set Pools 128122GN - User Manual

Intex Easy Set Pools 128122GN
33 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Zusammengeführte PDF Datei. Die Originale sind im folgenden Verzeichnis verlinkt. / Merged PDF File. Original files are linked in the following list. / Sloučený soubor PDF.
Originály jsou propojeny v následujícím adresáři. / Egyesített PDF fájl. Az eredetiek a következő könyvtárban találhatók. / Zlúčený súbor PDF. Originály sú prepojené v
nasledujúcom adresári. / Združena datoteka PDF. Izvirniki so povezani v naslednjem imeniku. / Spojena PDF datoteka. Izvornici su povezani u sljedećem imeniku.
128122GN - Easy Set Pools® Ø 305 x 76 cm
Filter Pump 2
Above Ground Pool 13
Overview Pool Size vs Pump Running Time 25
Air Valve For Water Revitalization Set 27
Setup Video 29
Repair Kit 31
Service Center 32

Table of Contents

Questions and Answers

  • A
    Albert JacobsAug 20, 2025
    How to fix Intex Water Pump filter motor that fails to start?
    • D
      denniszacharyAug 21, 2025
      If the Intex Water Pump filter motor fails to start, first, ensure the filter cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Next, try resetting the circuit breaker. If it trips repeatedly, there may be an electrical system defect, so turn off the breaker and consult an electrician. Finally, the motor might be too hot, so allow it to cool down.
  • B
    baxterjenniferAug 22, 2025
    What to do if Intex Easy Set Pools 128122GN Water Pump doesn’t pump water or flow is very slow?
    • H
      Heather TorresAug 22, 2025
      If the Intex Water Pump doesn’t pump water or the flow is very slow, check for obstructions in the intake hose. Clear any obstructions by discharging it inside the pool wall. Ensure there isn't an air leak on the intake line by tightening hose clamps and checking for hose damage, also check pool water level. Replace the cartridge if there's scale or buildup. If the pool is excessively dirty, clean the cartridge more often. Ensure the nozzle is installed at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. Also, confirm the pool inlet air adapter is connected to the pool inlet upper fitting.
  • K
    Kenneth BurnsAug 25, 2025
    Why doesn't my Intex Water Pump filter clean the pool?
    • K
      Kathleen BrownAug 25, 2025
      If your Intex Water Pump filter doesn't clean the pool effectively, start by adjusting the chlorine and pH levels, consulting your local pool supply store for guidance. Then, clean or replace the filter cartridge, checking it for holes and replacing it if damaged. If the pool is excessively dirty, operate the filter for longer periods. Also, ensure you clean the strainer screen at the inlet.
  • C
    Chloe WeberAug 27, 2025
    How to stop small leak from air jet valve when Intex Easy Set Pools 128122GN Water Pump is on?
    • B
      Bonnie BrownAug 27, 2025
      If you notice a small leak from the air jet valve when the Intex Water Pump is on, it may be due to accessories attached to the water circulation line. Remove all accessories, such as solar mats, auto pool cleaners, or LED lights, from the water circulation line. Place the air jet valve cap over the air jet valve. Do not cover the air jet valve with the valve cap under normal situations or when the pump is operating.
  • M
    Mallory PinedaAug 27, 2025
    How to fix Intex Water Pump top cover leaking?
    • A
      Audrey DelgadoAug 27, 2025
      If the Intex Water Pump top cover is leaking, remove the cover and check for the O-ring. If it’s missing, replace it. Also, ensure that the cover and air release valve are tightened manually.
  • H
    Heather GordonAug 29, 2025
    How to remove air lock from Intex Easy Set Pools 128122GN Water Pump?
    • A
      anthonyjohnsonAug 29, 2025
      To address an air lock in your Intex Water Pump, which is caused by air trapped in the pump housing and inlet hose, open the air release valve. Lift and lower the inlet hose until water starts flowing out of the air release valve, then close the valve.
  • B
    Benjamin CortezAug 31, 2025
    What to do if Intex Easy Set Pools 128122GN Water Pump hose is leaking?
    • N
      nicole06Aug 31, 2025
      If the hose on your Intex Water Pump is leaking, first, try tightening or changing the hose clamps. If that doesn't work, check if the hose o-ring dislodged when connecting the hose and put it back into the groove. If the hose is broken, replace it with a new one.
  • J
    Jacqueline HaleSep 2, 2025
    How to repair Pool Inlet Air Adaptor/Air Jet Valve leaking on Intex Easy Set Pools 128122GN?
    • D
      Dr. John LeSep 2, 2025
      If your Pool Inlet Air Adaptor or Air Jet Valve is leaking, try these steps: * Tighten or reinstall the hose clamps. * Tighten the air jet valve and make sure it’s facing up. * Plug in the pump and run it for a few seconds, then unplug it; repeat this three times. * Remove the air jet valve, flush out any dirt with water, and replace the valve. * If none of these steps work, replace the air jet valve with a new one.
  • E
    Elizabeth ThomasSep 3, 2025
    What to do if my Intex Swimming Pool filter motor fails to start?
    • M
      Melanie WarrenSep 4, 2025
      If your Intex Swimming Pool filter motor isn't starting, there could be a few reasons. First, ensure the filter cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If it is plugged in, check the GFCI/RCD circuit breaker and reset it. If it trips repeatedly, there may be an electrical defect requiring an electrician. Lastly, the motor might be too hot, and the overload protection has shut off. In this case, let the motor cool down.
  • K
    Kayla PerezSep 5, 2025
    Why is my Intex Swimming Pool filter not cleaning the pool?
    • C
      Chelsea CarterSep 6, 2025
      If your Intex Swimming Pool filter isn't effectively cleaning the pool, consider these possibilities: * The chlorine or pH levels might be improper. Adjust them, consulting your local pool supply store for guidance. * The filter cartridge could be dirty. Clean or replace it. * The cartridge might be damaged. Check for holes and replace if necessary. * The pool may be excessively dirty, requiring you to operate the filter for longer periods. * The strainer screen could be restricting water flow. Clean it at the inlet.

Intex Easy Set Pools 128122GN Specifications

General IconGeneral
BrandIntex
ModelEasy Set Pools 128122GN
CategoryWater Pump
LanguageEnglish

Related product manuals