To Next PageTo Next PageWhat to do if Intex Krystal Clear SX2100 Swimming Pool Pump doesn’t work?
If the Intex Swimming Pool pump isn’t working, ensure the pool is filled to the correct water level. Clean the strainer screens at the pool inlet. Tighten hose nuts and check the hose for damage to address any air leaks on the intake hose. For a faulty motor or jammed impeller, contact the Intex service center.
How to fix Intex Swimming Pool Pump motor that fails to start?
If the Intex Swimming Pool Pump filter motor fails to start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, check if the GFCI/RCD circuit breaker has tripped and reset it. If it repeatedly trips, there may be an electrical system defect requiring an electrician. Lastly, the motor may be too hot; allow it to cool down before restarting.
Why is the Intex Swimming Pool filter not pumping water or has very slow flow?
If your Intex Swimming Pool filter isn’t pumping water or the flow is very slow, start by clearing any obstructions in the intake hose by discharging it inside the pool wall. Check for air leaks on the intake line by tightening hose nuts and inspecting hoses for damage, also check pool water level. Clean the pre-filtering basket more often if the pool is excessively dirty. Backwash the filter if the sand media is clogged with dirt. Ensure the nozzle is at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. Remove about 1” of sand if there's crusting or caking on the filtering sand surface. Remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
What to do if the Intex Swimming Pool filter motor fails to start?
If the Intex Swimming Pool filter motor won't start, ensure it's properly plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter (GFCI) or RCD. Also, check if the GFCI/RCD circuit breaker has tripped and reset it. If it repeatedly trips, there may be an electrical defect requiring an electrician. If the motor is too hot, let it cool down before restarting.
How to troubleshoot Intex Swimming Pool Pump timer that is inaccurate or can't be set?
If the timer on your Intex Swimming Pool Pump is inaccurate or can't be set, turn off the pump and restart it 5 minutes later. Also, try re-setting the timer.
What to do if Intex Krystal Clear SX2100 pressure gauge doesn’t work?
If the pressure gauge on your Intex Swimming Pool Pump doesn’t work, clear any obstructions in the intake by unscrewing it from the 6-way valve.
What to do if Intex Krystal Clear SX2100 doesn't pump water or flow is very slow?
If your Intex Swimming Pool Pump doesn't pump water or the flow is very slow, first, clear any obstructions in the intake hose. Next, tighten hose nuts and check for damage, also check the pool water level to prevent air leaks. Clean the pre-filtering basket more often and backwash the filter. Ensure the nozzle and strainer connections are correctly placed. Remove about 1" of sand if the filtering sand surface has crusted or caked. Remove any pool vacuuming device attached to the system line. Finally, make sure the inlet threaded air connector is connected to the pool inlet upper hole.
How to troubleshoot an inaccurate or non-setting timer on an Intex Krystal Clear SX2100?
If the timer on your Intex Swimming Pool Pump is inaccurate or can't be set, turn off the pump and restart it after 5 minutes. Then, try resetting the timer again.
What to do if my Intex Swimming Pool Pump filter doesn't clean the pool?
If your Intex Swimming Pool Pump doesn't clean the pool, adjust the chlorine and pH levels, consulting your local swimming pool supply stores for guidance. Ensure the tank is loaded with filter sand according to the sand loading instructions. Set the 6-way valve to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet, if it’s restricting the water flow.
How to fix Intex Krystal Clear SX2100 filter motor that fails to start?
If the Intex Swimming Pool Pump filter motor fails to start, ensure it is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the GFCI/RCD circuit breaker; if it trips repeatedly, have an electrician check your electrical system. If the motor is too hot, let it cool down before restarting.
General| Voltage | 110-120V |
|---|---|
| Power | 0.3 HP |
| Type | Sand Filter Pump |
| Inlet/Outlet Size | 1.5 inches |
| Pump Flow Rate | 2100 GPH |
| System Flow Rate | 1, 600 gph (6.0 m3/hr) |
| Timer | 24-hour automatic timer |
Emphasizes careful reading and adherence to all instructions before use.
Highlights critical warnings regarding electrical shock, operation, and potential injury.
Warns about operating the pump without water flow, which can cause pressure buildup and hazards.
Lists required tools and guidance for selecting and preparing the pump's location.
Covers pump location, mounting, pre-filter setup, and sand tank installation.
Details connecting hoses and installing the 6-way valve for the pump system.
Explains the different settings of the 6-way valve and their respective functions.
Details control panel features, LED readings, timer, and manual operation.
Guides users through initial setup, backwashing, and normal filtering procedures.
Instructions for cleaning and maintaining the motor's pre-filter assembly.
Common issues, causes, and solutions for filter pump problems.
Guidance on draining, cleaning, and storing the filter pump for the off-season.
Details the warranty coverage, terms, and conditions for the sand filter pump.
