What to do if Intex SF60220-1 Water Pump filter motor fails to start?
First, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the GFCI/RCD circuit breaker is tripped, reset it. If it repeatedly trips, there may be an electrical defect, so turn off the breaker and consult an electrician. Also, the motor may be too hot; let it cool down before restarting.
Why is my Intex SF60220-1 filter not pumping water or the flow is very slow?
There might be several reasons for this issue. Check for clogged inlet or discharge and clear any obstructions in the intake hose. Look for air leaks on the intake line by tightening hose nuts and inspecting for damage, also check pool water level. If the pool is excessively dirty, clean the pre-filtering basket more often. If the sand media is clogged, backwash the filter. Ensure the nozzle and strainer connections are not reversed. If there's crusting or caking on the filtering sand surface, remove about 1' of sand if necessary. Also, remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
Why is my Intex SF60220-1 filter not cleaning the pool?
This could be due to several factors. Check and adjust the chlorine and pH levels. Make sure the 6-way valve is set to the 'FILTER' position. If the pool is excessively dirty, operate the filter for longer periods. Also, inspect and clean the strainer screen at the inlet if it's restricting water flow.
How to fix leaking hose on Intex SF60220-1 Water Pump?
Ensure the hose nut is securely tight by tightening or reinstalling it. Also, verify that the hose connection fitting o-ring/L-shape o-ring is in place and not damaged.
Why is sand flowing back into the pool from my Intex Water Pump?
The sand might be too small. Use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Alternatively, the sand bed may be calcified, requiring you to change the sand.
Why is my Intex SF60220-1 timer inaccurate or can't be set?
The inner timer might be defective. Turn off the pump and restart it 5 minutes later. You can also try re-setting the timer.
Why is the 6-way valve/cover leaking on my Intex Water Pump?
The sand tank o-ring might be missing or dirty. Remove the 6-way valve cover and ensure the o-ring is in place, and clean it with garden hose water if dirty. Also, the flange clamp might not be tight; tighten it with the wrench supplied.
What to do if Intex Water Pump inlet threaded air connector/air jet valve is leaking?
Ensure the plunger valve is well-fitted by tightening or reinstalling it. Check that the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON for a few seconds, then turn it OFF, and repeat this process 3 times. If the air jet valve internal seal is dirty, remove the air jet valve, flush out any dirt with water, and replace the valve back.
What to do if the pressure gauge doesn't work on Intex SF60220-1?
Clear any obstructions in the intake of the pressure gauge by unscrewing it from the 6-way valve.
Read, understand, and follow all instructions carefully before installing and using the product.
Covers tools required, pump mounting, and motor pre-filter assembly setup.
General| Model | SF60220-1 |
|---|---|
| Category | Water Pump |
| Frequency | 60 Hz |
| Hose diameter | 1.25 inches |
| Voltage | 110-120V |
| Max Flow Rate | 2200 GPH |
| Inlet Size | 1.25 inches |
| Outlet Size | 1.25 inches |
| Type | Sand Filter Pump |
To Next Page