Intex SX 2100 User Manual (English)

Questions and Answers:

J
James EnglishSep 3, 2025
What to do if my Intex SX 2100 Swimming Pool inlet threaded air connector / air jet valve is leaking?
- K
  Kimberly GarrettSep 4, 2025
  If the inlet threaded air connector or air jet valve is leaking, try tightening or reinstalling the plunger valve. Ensure the air jet valve is tight and facing up. If the internal seal is blocked, turn the pump on for a few seconds, then off, and repeat three times. If the seal is dirty, remove the air jet valve, flush out dirt with water, and replace the valve. If the valve is broken, replace it with a new one.
J
Jeremiah GatesSep 2, 2025
Why is my Intex SX 2100 timer inaccurate or can't be set?
- J
  Jeffrey StevensSep 2, 2025
  If the timer is inaccurate or cannot be set, the inner timer might be defective. Try turning off the pump and restarting it 5 minutes later. If that doesn't work, reset the timer. If problems persist, contact Intex service center.
M
Mary NewmanSep 1, 2025
How to fix a leak from the hose of my Intex SX 2100 Swimming Pool?
- S
  Sandra JohnsonSep 1, 2025
  To address a leaking hose, first, try tightening or reinstalling the hose nut securely. If the leak persists, check for a missing or damaged o-ring/L-shape o-ring at the hose connection fitting and ensure it is in place.
V
Vincent SimmonsAug 30, 2025
Why is sand flowing back into my Intex Swimming Pool?
- E
  emartinAug 30, 2025
  If sand is flowing back into the pool, it could be due to the sand being too small. Use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Alternatively, the sand bed may be calcified, in which case you should change the sand.
E
ebakerAug 29, 2025
What to do if my Intex Swimming Pool filter doesn’t clean the pool?
- H
  Heather EvansAug 29, 2025
  If your filter isn’t cleaning the pool, consider these possible causes. Adjust the chlorine and pH levels, consulting your local swimming pool supply store for guidance. Ensure the tank is loaded with filter sand according to the sand loading instructions. Verify that the 6-way valve is set to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet to prevent restricted water flow.
D
Daniel NelsonAug 27, 2025
What to do if Intex SX 2100 filter motor fails to start?
- G
  gardnerandrewAug 27, 2025
  If the filter motor fails to start, there are several possible causes. First, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the GFCI/RCD circuit breaker has tripped, reset it. If it repeatedly trips, your electrical system may have a defect, so turn off the breaker and call an electrician. It's also possible the motor is too hot; in this case, let it cool down before restarting.
J
John CaldwellAug 25, 2025
Why is my Intex SX 2100 Swimming Pool 6-way valve/cover leaking?
- R
  Raymond BranchAug 26, 2025
  If the 6-way valve or cover is leaking, first remove the 6-way valve cover and ensure the o-ring is in place. If the o-ring is dirty, clean it with garden hose water. Also, make sure the flange clamp is securely tightened. If the issue persists, the 6-way valve may be damaged, and you should contact an Intex service center.
N
nelsonandreaAug 23, 2025
What to do if my Intex Swimming Pool pump doesn’t work?
- K
  Kim FarmerAug 23, 2025
  If the pump isn’t working, first, ensure the pool is filled to the correct water level. Next, clean the strainer screens at the pool inlet. Also, check for air leaks on the intake hose by tightening hose nuts and inspecting the hose for damage. If these steps don’t resolve the issue, contact an Intex service center, as the motor may be faulty or the impeller may be jammed.