To Next PageTo Next PageHow to improve cleaning performance of Intex SX 1500 Swimming Pool filter?
If your Intex Swimming Pool filter isn't cleaning the pool, adjust the chlorine and pH levels. If there is no filtering media in the tank, load it with filter sand. Ensure the 6-way valve is set to the 'FILTER' position. For an excessively dirty pool, operate the filter for longer periods, and clean the strainer screen at the inlet if it's restricting the water flow.
What to do if Intex Swimming Pool air jet valve is leaking?
To resolve leaks from the inlet threaded air connector or air jet valve on your Intex Swimming Pool, tighten or reinstall the plunger valve. Ensure the air jet valve is tight and facing up. If the internal seal is blocked or dirty, turn the pump ON and OFF for a few seconds, repeating three times, or remove the air jet valve, flush out dirt with water, and replace it. If the air jet valve is broken, replace it.
What to do if my Intex SX 1500 filter motor fails to start?
If the filter motor of your Intex Swimming Pool fails to start, first ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If that doesn't work, reset the GFCI/RCD circuit breaker. If it trips repeatedly, your electrical system may have a defect, so turn off the breaker and call an electrician. Finally, the motor may be too hot; let it cool down before restarting.
How to improve cleaning if my Intex Swimming Pool filter doesn’t clean well?
If your Intex Swimming Pool filter isn’t cleaning the pool effectively, adjust the chlorine and pH levels, consulting your local swimming pool supply stores for guidance. Ensure the tank is loaded with filter sand, following the sand loading instructions. Verify that the 6-way valve is set to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet to remove any restrictions to the water flow.
What to do if my Intex SX 1500 pump doesn’t work?
If the pump of your Intex Swimming Pool doesn’t work, ensure the water level is correct. Clean the strainer screens at the pool inlet. Check for air leaks on the intake hose by tightening the hose nuts and inspecting the hose for damage. If none of these actions work, contact an Intex service center, as the motor may be faulty or the impeller jammed.
Why is the 6-way valve/cover leaking in my Intex SX 1500?
If the 6-way valve/cover of your Intex Swimming Pool is leaking, first, remove the 6-way valve cover and ensure the o-ring is in place. If the o-ring is dirty, clean it with garden hose water. Make sure the flange clamp is securely tightened. If the valve is damaged, contact an Intex service center.
How to fix a leaking hose on my Intex SX 1500?
If the hose of your Intex Swimming Pool is leaking, tighten or reinstall the hose nut to ensure it is securely tight. Also, check that the hose connection fitting o-ring or L-shape o-ring is in place and not damaged.
Why is sand flowing back into my Intex SX 1500?
If sand is flowing back into your Intex Swimming Pool, it may be because the sand is too small. Use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Alternatively, the sand bed may be calcified, in which case you should change the sand.
What to do if the air jet valve is leaking in my Intex SX 1500?
If the inlet threaded air connector or air jet valve of your Intex Swimming Pool is leaking, tighten or reinstall the plunger valve. Ensure the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON and run for a few seconds, then turn OFF, repeat 3 times. If the air jet valve internal seal is dirty, remove the air jet valve, flush dirt out with water, and replace the valve back. If the air jet valve is broken, replace it with a new one.
How to fix an inaccurate timer on my Intex Swimming Pool?
If the timer on your Intex Swimming Pool is inaccurate or can't be set, turn off the pump and restart it 5 minutes later. Also, try re-setting the timer. If problems persist, contact an Intex service center.
General| Shape | Round |
|---|---|
| Included Accessories | Filter Pump, Ladder, Ground Cloth, Pool Cover |
| Height | 48 inches |
| Material | PVC |
| Frame Material | Steel |
Critical safety warnings regarding product usage and potential hazards.
Guidance on connecting hoses for the sand filter pump to the pool.
Details valve positions, functions, and control panel elements for operation.
Steps for initial system setup, backwashing, rinsing, and normal filtering.
Instructions for operating the system under timer mode, manual mode, and power saving.
Recommended operating times for Intex pools based on size.
Recommended operating times for non-Intex pools based on water capacity.
