Intex PureSpa SJB-HS-22

Other manuals for Intex PureSpa SJB-HS-22

Owner's Manual43 pages

Questions and Answers

T
Teresa RossSep 4, 2025
Why is the filtration pump not working on my Intex PureSpa SJB-HS-22?
- B
  bauerrichardSep 4, 2025
  If the filtration pump on your Intex Swimming Pool isn't working, start by cleaning or replacing the filter cartridge. Also, check and clean the filtration inlet and outlet regularly to ensure they are not clogged. If the filter pump motor has failed, contact an Intex Service Center.
A
Alyssa EnglishAug 25, 2025
How to fix Intex Hot Tub error E90?
- P
  Penny CoffeyAug 25, 2025
  To address the E90 error on your Intex Hot Tub, start by turning off and unplugging the control unit. Ensure the outlet cover grid is clean and free from obstructions. Clean or replace the cartridge. Verify that the inlet/outlet connections on the spa tub and filter pump are not blocked. Keep the spa water properly sanitized to ensure a clean and unclogged filter cartridge. Release trapped air by unscrewing the drain valve cap, and then run the filter function. If the problem continues, contact Intex Service Center.
S
Samuel RobinsonAug 25, 2025
How to clean Intex PureSpa SJB-HS-22 Swimming Pool water?
- J
  Joshua FuentesAug 26, 2025
  If the water in your Intex Swimming Pool is not clean, ensure the cartridge assembly is properly attached. Also, increase the filtration time and clean or replace the filter cartridge as needed. Maintain proper water sanitation following the chemical manufacturer’s instructions. Regularly check and clean the filtration inlet and outlet.
S
Sara AlexanderSep 12, 2025
What to do if the Intex Hot Tub filtration pump is not working?
- C
  Christie SchwartzSep 12, 2025
  If the filtration pump on your Intex Hot Tub isn't working, start by cleaning or replacing the filter cartridge. Also, check the filtration inlet and outlet for clogs and clean them regularly. If the filter pump motor has failed, contact Intex Service Center.
B
Brent HarrisSep 22, 2025
What to do if the Intex PureSpa SJB-HS-22 display or spa control unit does not work?
- C
  Christopher MillerSep 22, 2025
  If the Intex Swimming Pool's display isn't working, first ensure the spa is plugged in and switched on. Check that the control panel cable plug is firmly attached to the control base receptacle. Also, verify the power source and reset the RCD. If the RCD is broken, contact an Intex Service Center.
D
David StuartSep 8, 2025
How do I fix an E90 error on my Intex Swimming Pool?
- D
  Daniel GreeneSep 8, 2025
  If your Intex Swimming Pool displays an E90 error code, turn off and unplug the control unit. Ensure the outlet cover grid is clean and free from obstructions.
B
Brad WoodsSep 1, 2025
What to do if the bubble air blower does not work on my Intex PureSpa SJB-HS-22 Swimming Pool?
- M
  Michael ReedSep 1, 2025
  If the bubble air blower on your Intex Swimming Pool isn't working, turn off and unplug the spa. Let it cool down before restarting.
C
Clayton LindseySep 23, 2025
What does error code E95 mean on my Intex PureSpa SJB-HS-22?
- J
  jose99Sep 23, 2025
  If your Intex Swimming Pool is showing error code E95, the water temperature is around 50°C (122°F). Turn off and unplug the control unit. When the water has cooled down, plug the RCD and restart. You can also turn the heater off, then press the filter and jet buttons to lower the water temperature.
C
Christina GreenSep 15, 2025
What to do if the jet air control knob is not working on my Intex Hot Tub?
- R
  Rebecca MatthewsSep 15, 2025
  If the jet air control knob on your Intex Hot Tub isn't working, clean any dirt inside the jet nozzles. If the jet airflow plumbing inside the spa tub is damaged, contact Intex Service Center.
C
cfrenchAug 28, 2025
What to do if the Intex PureSpa SJB-HS-22 has no display or the spa control unit does not work?
- S
  sanderscherylAug 28, 2025
  If the Intex Swimming Pool's display isn't working or the spa control unit is unresponsive, first, ensure the spa is properly plugged in and switched on. Then, check that the control panel cable plug is firmly attached to the control base receptacle. Also, verify the power source and reset the RCD if it has tripped. If the RCD is broken, further assistance is needed.