To Next PageTo Next PageWhat to do if the bubble air blower does not work on my Intex PureSpa SJB-HS-22 Swimming Pool?
If the bubble air blower on your Intex Swimming Pool isn't working, turn off and unplug the spa. Let it cool down before restarting.
How to level pump connectors with spa connectors on Intex PureSpa SJB-HS-22?
If the pump connectors are not level with the spa connectors on your Intex Swimming Pool, elevate the pump with wood or another type of insulated material to bring the pump’s connectors level with the spa’s connectors.
Why does my Intex PureSpa SJB-HS-22 tub have a strange shape?
If the tub of your Intex Swimming Pool has a strange shape, avoid exposing the spa to direct sunlight for extended periods. Check the air pressure and release air if necessary, especially during hot weather, to avoid damage to the tub.
How to fix an Intex Swimming Pool tub that loses air pressure?
If your Intex Swimming Pool tub is losing air pressure, ensure the air valve cap is securely closed. If the air valve base is loose, fill the spa tub with air and tighten the air valve base. If there's a hole, cut, or split on the spa tub, apply liquid soap and water to find the leak, then clean and dry the area before applying the repair patch.
How to stop leaking between spa tub and control unit connectors on Intex Swimming Pool?
If there's leaking between the spa tub connectors and control unit connectors on your Intex Swimming Pool, tighten the inlet and outlet connections. Also, coat the O-ring with petroleum jelly for a waterproof seal. Ensure the inlet/outlet O-ring is in place, clean, and not damaged.
Why is my Intex PureSpa SJB-HS-22 so noisy in filtration mode?
If your Intex Swimming Pool is too noisy in filtration mode only, ensure the control panel, back cover, and all inlet/outlet connections are securely connected. Make sure the ground is level, firm, and smooth. If the spa filter motor has failed, replace it with a new one.
How to fix Intex PureSpa SJB-HS-22 when no display or spa control unit does not work?
If the Intex Swimming Pool's display isn't working, or the spa control unit fails to operate, first ensure the spa is properly plugged in and switched on. Check that the control panel cable plug is firmly attached to the control base receptacle. Also, verify the power source and reset the RCD if it has tripped. If the RCD is broken, contact an Intex Service Center.
What to do if my Intex PureSpa SJB-HS-22 Swimming Pool is not heating properly?
If your Intex Swimming Pool isn't heating properly, first, make sure the temperature is set high enough and the spa cover is attached to retain heat. A dirty filter cartridge can also cause heating issues, so clean or replace it. If the heater is in STANDBY mode, press the flame button twice to heat the water to the set temperature. If the heating element has failed, contact an Intex Service Center.
Why is the filtration pump not working on my Intex PureSpa SJB-HS-22?
If the filtration pump on your Intex Swimming Pool isn't working, start by cleaning or replacing the filter cartridge. Also, check and clean the filtration inlet and outlet regularly to ensure they are not clogged. If the filter pump motor has failed, contact an Intex Service Center.
Why are the jets output weak in my Intex PureSpa SJB-HS-22 Swimming Pool?
If the jets on your Intex Swimming Pool have weak output, ensure the water level is between the MIN and MAX levels. Check that the suction inlet inside the tub is not covered or blocked. Also, clean any dirt inside the jet nozzles. If the jet nozzles plumbing pipes are damaged, contact an Intex Service Center.
General| Brand | Intex |
|---|---|
| Model | PureSpa SJB-HS-22 |
| Category | Swimming Pool |
| Language | English |
Lists critical safety hazards like drowning, electric shock, and warnings about water temperature and usage.
Instructions for assembling the control unit and inflating the spa tub wall.
Detailed steps for inflating the spa tub wall and the spa cover air bladder.
Procedures for deflating the spa and installing the control unit.
Details the function of each button on the control panel for operating the spa.
Lists common issues like no display, tripped breaker, and weak jets with solutions.
Addresses issues like tub shape, air loss, low chlorine, and LED codes.
