To Next PageTo Next PageWhy is the filtration pump not working on my Intex Swimming Pool?
If the filtration pump on your Intex Swimming Pool isn't working, start by cleaning or replacing the filter cartridge. Also, check and clean the filtration inlet and outlet regularly to ensure they are not clogged. If the filter pump motor has failed, contact an Intex Service Center.
How to fix Intex Hot Tub error E90?
To address the E90 error on your Intex Hot Tub, start by turning off and unplugging the control unit. Ensure the outlet cover grid is clean and free from obstructions. Clean or replace the cartridge. Verify that the inlet/outlet connections on the spa tub and filter pump are not blocked. Keep the spa water properly sanitized to ensure a clean and unclogged filter cartridge. Release trapped air by unscrewing the drain valve cap, and then run the filter function. If the problem continues, contact Intex Service Center.
How to clean Intex Swimming Pool water?
If the water in your Intex Swimming Pool is not clean, ensure the cartridge assembly is properly attached. Also, increase the filtration time and clean or replace the filter cartridge as needed. Maintain proper water sanitation following the chemical manufacturer’s instructions. Regularly check and clean the filtration inlet and outlet.
How to clean my Intex PureSpa SJB-HS-30-1C water when it is not clean?
If the water in your Intex Swimming Pool is not clean, ensure the cartridge assembly is properly attached. Insufficient filtering time could be the issue, so increase it. Also, a dirty filter cartridge can cause this, so clean or replace it. Maintain proper water sanitation, following the chemical manufacturer’s instructions, and check and clean the filtration inlet and outlet regularly.
Why are the jets output weak in my Intex PureSpa SJB-HS-30-1C Swimming Pool?
If the jets on your Intex Swimming Pool have weak output, ensure the water level is between the MIN and MAX levels. Check that the suction inlet inside the tub is not covered or blocked. Also, clean any dirt inside the jet nozzles. If the jet nozzles plumbing pipes are damaged, contact an Intex Service Center.
What causes insufficient chlorine in my Intex PureSpa SJB-HS-30-1C Swimming Pool and how to fix it?
If there is insufficient chlorine in your Intex Swimming Pool, increase the sanitation system operating time and ensure the heater is off during the sanitation process. Use a spa cover when the spa is not in use or when the sanitation system is operating to prevent chlorine loss due to sunlight. If the bather load has increased, increase the sanitation system operating time and test the water using test strips. Also, check and clean the electrolytic cell if it's clogged or dirty.
What to do if the bubble air blower does not work on my Intex PureSpa SJB-HS-30-1C?
If the bubble air blower on your Intex Swimming Pool isn't working, turn off and unplug the spa. Let it cool down before restarting.
How to level pump connectors with spa connectors on Intex PureSpa SJB-HS-30-1C Swimming Pool?
If the pump connectors are not level with the spa connectors on your Intex Swimming Pool, elevate the pump with wood or another type of insulated material to bring the pump’s connectors level with the spa’s connectors.
How to fix an Intex Swimming Pool that is not heating properly?
If your Intex Swimming Pool isn't heating properly, first, increase the set temperature and ensure the spa cover is attached. Make sure the filter cartridge is clean; replace it if necessary. If the heater is in STANDBY mode, press the flame button twice to heat the water to the set temperature. If the heating element has failed, further assistance is needed.
What to do if the Intex Swimming Pool has no display or the spa control unit does not work?
If the Intex Swimming Pool's display isn't working or the spa control unit is unresponsive, first, ensure the spa is properly plugged in and switched on. Then, check that the control panel cable plug is firmly attached to the control base receptacle. Also, verify the power source and reset the RCD if it has tripped. If the RCD is broken, further assistance is needed.
General| Model | SJB-HS-30-1C |
|---|---|
| Brand | Intex |
| Type | Inflatable Hot Tub |
| Water Filtration | Yes |
| Heating System | Yes |
| Height | 71 cm (28 inches) |
| Material | Fiber-Tech Construction |
| Heater Temperature Range | 68-104°F |
| Included Accessories | Inflation Hose |
Covers DANGER, WARNING, and CAUTION notices for safe operation of the spa.
Guidelines for choosing and preparing the installation location for the spa.
Explanation of the control panel buttons, display, and functions.
Instructions for activating and setting the sanitation system.
Guide to maintaining optimal water chemistry and balance.
Solutions for common problems with the spa's operation.
