EasyManua.ls Logo

Intex SX 2800 - User Manual

Intex SX 2800
67 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Zusammengeführte PDF Datei. Die Originale sind im folgenden Verzeichnis verlinkt. / Merged PDF File. Original files are linked in the following list. / Sloučený soubor PDF.
Originály jsou propojeny v následujícím adresáři. / Egyesített PDF fájl. Az eredetiek a következő könyvtárban találhatók. / Zlúčený súbor PDF. Originály sú prepojené v
nasledujúcom adresári. / Združena datoteka PDF. Izvirniki so povezani v naslednjem imeniku. / Spojena PDF datoteka. Izvornici su povezani u sljedećem imeniku.
126364GN - Frame Pool Set Ultra Quadra XTR 732 x 366
x 132 cm
Sand Filter Unit 2
Ladder 28
Above Ground Pool 42
Overview Pool Size vs Pump Running Time 57
Air Valve For Water Revitalization Set 59
Transition Liner For U-Shaped Side Support 61
Setup Video 62
Mounting 64
Repair Kit 65
Service Center 66

Questions and Answers

  • J
    Johnathan LewisNov 26, 2025
    Why doesn't my Intex SX 2800 filter pump water or why is the flow very slow?
    • A
      April BrownNov 26, 2025
      If your filter isn’t pumping water or the flow is very slow, several factors could be responsible: * Check for clogged inlet or discharge and clear any obstructions in the intake hose. * Tighten hose nuts, inspect hoses for damage, and verify the pool water level to address potential air leaks. * Clean the pre-filtering basket more often if the pool is excessively dirty. * Backwash the filter if the sand media is clogged with dirt. * Ensure the nozzle is at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. * Remove about 1” of sand if crusting or caking has occurred on the filtering sand surface. * Remove any pool vacuuming device attached to the system line. * Ensure the inlet threaded air connector is connected to the pool in...
  • M
    martinandrewSep 13, 2025
    What causes a 6-way valve leak in my Intex Swimming Pool and how can I fix it?
    • A
      ashleybassSep 14, 2025
      If the 6-way valve or cover is leaking on your Intex Swimming Pool, remove the 6-way valve cover and ensure the sand tank o-ring is in place. Clean the sand tank o-ring with garden hose water. Tighten the flange clamp securely. If the issue persists, contact the Intex service center, as the 6-way valve may be damaged.
  • B
    Bryan RodriguezSep 12, 2025
    What to do if the filter in my Intex SX 2800 isn't cleaning properly?
    • R
      Robert MunozSep 12, 2025
      If the filter of your Intex Swimming Pool isn’t cleaning the pool effectively, you should adjust the chlorine and pH levels, consulting your local swimming pool supply store for guidance. Ensure the tank is loaded with filter sand according to the 'sand loading instructions'. Set the valve to the 'FILTER' position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet if it's restricting water flow.
  • L
    Luke MorrisAug 27, 2025
    What to do if Intex SX 2800 Swimming Pool filter motor fails to start?
    • A
      Angelica JamesAug 27, 2025
      If the filter motor fails to start, there are several possible causes. First, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the GFCI/RCD circuit breaker has tripped, reset it. If it repeatedly trips, your electrical system may have a defect, so turn off the breaker and call an electrician. It's also possible the motor is too hot; in this case, let it cool down before restarting.
  • C
    christiancoreyAug 29, 2025
    What to do if my Intex SX 2800 Swimming Pool filter doesn’t clean the pool?
    • V
      Virginia WilliamsAug 29, 2025
      If your filter isn’t cleaning the pool, consider these possible causes. Adjust the chlorine and pH levels, consulting your local swimming pool supply store for guidance. Ensure the tank is loaded with filter sand according to the sand loading instructions. Verify that the 6-way valve is set to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet to prevent restricted water flow.
  • S
    salazarbrandonAug 30, 2025
    Why is sand flowing back into my Intex SX 2800?
    • L
      lisa97Aug 30, 2025
      If sand is flowing back into the pool, it could be due to the sand being too small. Use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Alternatively, the sand bed may be calcified, in which case you should change the sand.
  • C
    cwalkerSep 1, 2025
    How to fix a leak from the hose of my Intex Swimming Pool?
    • H
      howellalexanderSep 1, 2025
      To address a leaking hose, first, try tightening or reinstalling the hose nut securely. If the leak persists, check for a missing or damaged o-ring/L-shape o-ring at the hose connection fitting and ensure it is in place.
  • D
    Derek EatonSep 2, 2025
    Why is my Intex SX 2800 timer inaccurate or can't be set?
    • T
      Tammy CalderonSep 2, 2025
      If the timer is inaccurate or cannot be set, the inner timer might be defective. Try turning off the pump and restarting it 5 minutes later. If that doesn't work, reset the timer. If problems persist, contact Intex service center.
  • K
    Kathy PalmerSep 15, 2025
    What to do if the air jet valve is leaking on my Intex SX 2800 Swimming Pool?
    • M
      Michael HardySep 15, 2025
      If the inlet threaded air connector or air jet valve is leaking on your Intex Swimming Pool, try tightening or reinstalling the plunger valve. Ensure the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON and run for a few seconds, then turn OFF, repeating this 3 times. If the air jet valve internal seal is dirty, remove the air jet valve, flush dirt out with water, and replace the valve. If the air jet valve is broken, replace it with a new one.
  • R
    Raymond DavisSep 12, 2025
    How to fix a leaking hose on my Intex Swimming Pool?
    • A
      Andrew EdwardsSep 12, 2025
      If you notice a leak from the hose of your Intex Swimming Pool, try tightening or reinstalling the hose nut. Also, check that the hose connection fitting o-ring or L-shape o-ring is in place and undamaged.

Summary

Intex Sand Filter Pump Safety Rules

General Safety Precautions

Rules for supervision, electrical safety, and product placement.

Hazard Warnings

Specific warnings about electric shock, entrapment, and pressure hazards.

Sand Filter Pump Setup and Installation

Sand Filter Pump Operation Guide

6-Way Valve Functions

Explanation of each valve position and its water flow direction.

Control Panel Operations

Guide to using the control panel buttons and understanding LED displays.

Operating Modes

How to operate the pump using the timer or in manual (continuous) mode.

Pool Troubleshooting and Aquatic Safety

Sand Filter Pump Limited Warranty

Intex SX 2800 Specifications

General IconGeneral
BrandIntex
ModelSX 2800
CategorySwimming Pool
LanguageEnglish

Related product manuals