Why does my IPC CT15 leave the floor wet?
If your IPC Scrubber leaves the floor wet, several factors could be at play. Make sure that: - The squeegee blades are not worn. - There is no debris between the two squeegee blades. - There is no debris in the suction hose. - The dirty water tank is not full. - The detergent tank lid is closed correctly. - The suction hose is correctly attached to the squeegee.
What to do if my IPC CT15 Scrubber doesn't come on?
If your IPC Scrubber doesn't start, check the battery charge if you have a battery version. For cable versions, verify the power cable is plugged into a functioning socket.
Why does my IPC CT15 leave stripes of wet floor?
If your IPC Scrubber leaves stripes of wet floor, it may be caused by several reasons. Check that the floor has been brushed before using the machine, there is no debris between the two squeegee blades, the squeegee blades are not worn, and the squeegee is correctly adjusted.
How to prevent my IPC Scrubber from leaving the floor dirty?
To prevent your IPC Scrubber from leaving the floor dirty, check that the type of brush in use is suitable for the type of dirt and floor.
What to do if the squeegee of my IPC Scrubber does not clean or has poor suction?
If the squeegee on your IPC Scrubber isn't cleaning well or has poor suction, consider these potential issues: * The rubber blades may be worn, requiring replacement. * The squeegee or hose might be blocked or damaged, needing to be unblocked or repaired. * The float switch could be tripped, clogged, or broken, so empty the dirty water drum or reset the float switch. * The suction hose might be blocked, requiring unblocking. * The suction hose may be disconnected or damaged, needing connection or repair.
How to fix IPC CT15 Scrubber when the brush doesn’t rotate?
If the brush on your IPC Scrubber isn't rotating, here are a few things to check: 1. If the brush button LED is off, press the brush button. 2. Ensure you've pressed the brush lever. 3. If the brush motor thermal cutout has tripped (motor overheated), release the brush lever, press the brush button until the LED is off, and let the machine cool down for at least 45 minutes. 4. Check if the batteries are flat; if so, charge them.
What to do if no detergent is delivered by IPC CT15?
If your IPC Scrubber is not delivering detergent, check the following: * Ensure the detergent button LED is on; if not, press the detergent button. * Verify the detergent tank isn't empty; if it is, fill it. * Confirm the brush motor is on by operating the brush lever. * Check for blockages in the detergent hose and clear them. * Inspect the tap for dirt or faults; clean or replace if necessary. * Examine the solenoid valve for faults; replace if needed. * Clean the filter if it's dirty.
Why does detergent flow not stop in my IPC Scrubber?
If the detergent flow in your IPC Scrubber won't stop, the solenoid valve might be faulty and needs replacement.
What to do if the battery discharges too fast during use of my IPC Scrubber?
If the battery on your IPC Scrubber discharges too quickly, even after correct charging, consider these possibilities: * If the battery is new, it may need to be "run-in" by performing 20-30 charge and discharge cycles to reach maximum performance. * If you're using the machine at maximum capacity for extended periods, consider using higher-capacity batteries or swapping to pre-charged batteries. * If the electrolyte has evaporated, top up all elements with distilled water until the plates are covered, then recharge the battery.
Details dipswitch settings for CT15, CT30 ECO, and CT30-CT45 chargers.
Lists potential hazards associated with machine components.
Key safety rules and precautions for machine use.
Guidelines for safely moving the packaged machine.
Guides for installing, removing, and charging batteries.
Explains machine controls, indicator lights, and basic operation.
Steps to prepare and operate the machine effectively.
Guide to diagnosing and fixing typical operational issues.
Explains error codes displayed on battery-powered machines.
General| Model | IPC CT15 |
|---|---|
| Category | Scrubber |
| Solution Tank | 15 L |
| Power Source | Battery |
| Voltage | 24 V |
| Brush Motor Power | 250 W |
| Water Tank Capacity | 15 L |
| Brush Speed | 140 rpm |
To Next Page
