the appliance.
Avoid body contact with grounded surfaces •
such as pipes, radiators, ranges and refrigerators.
This increases risk of electric shock if your body is
grounded.
CAUTION: touching electried parts may
cause death by electric shock or burn.
Never move the appliance by pulling at the •
cables.
Do not abuse the cord. Keep it away from heat, •
oil, sharp edges or moving parts.
Always guide the connection line safely.•
Do not use power tools near ammable liquids •
or gases.
Always disconnect the appliance from the mains •
supply before transporting it to other places.
CAUTION: The appliance should always
be switched o at the mains before
disconnecting any plug and socket
connector or extension cables.
Never pass the appliance over the extension •
cable while the tool is working. Make sure you
always know where the cable is.
Do not wire an extension cable directly into your •
device yourself. Instead, take the device to your
nearest authorized Service Centre.
ATTENTION! DANGER OF ELECTRIC SHOCK!
Consider working area environment. Do not expose
power tools to rain. Do not use power tools in
damp or wet locations. Keep work area well lit and
dry. Try to prevent the device from getting wet or
being exposed to humidity. Do not leave it outside
overnight. Water entering a power tool will increase
the risk of electric shock.
The power supply cable should be checked •
regularly and, before using it, make sure the cable
is not damaged or worn out. If the cable is not in
good condition, do not use the appliance; take it to
an authorized service centre.
When tool is used outdoor, only use an extension •
cable that is suitable for outdoor work and which is
marked for this specic use. Keep it away from the
working area, from damp, wet or oily surfaces and
away from heat and fuels.
To avoid danger, damaged power cord should •
be replaced by manufacturer or its agent, or similar
qualied person.
Immediately unplug the tool when its cable is •
damaged or cut.
Avoid any accidental starting: make sure the •
switch is “o” before plugging it in.
Remove adjusting keys or wrenches before •
turning the tool on.
Do not use the tool if the switch does not turn •
the tool on or o. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
WARNING! During the use of the tool, some
dust containing chemicals known to cause
cancer, may occur. Some of these chemicals
are: lead from lead based paints, crystalline silica from
bricks and cement and other masonry products,
arsenic and chromium from chemically treated lumber
and other dangerous products. If dust is present, your
risk from these exposures varies, depending on how
often you do this type of work. To reduce your
exposure to these chemicals, any time you do
pulverulent operations, work in a well ventilated
area and work with approved safety equipment,
such as dust masks that are specially designed to
lter out microscopic particles.
If the appliance strikes a foreign body, examine •
the device for signs of damage and carry out any
necessary repairs before restarting and continuing
to work.
If the appliance starts to vibrate abnormally, turn •
it o and check for the cause immediately. Vibration
is generally a warning of trouble.
Always switch o the appliance and wait until •
the device completely stops whenever you leave the
machine, before carrying out maintenance, before
checking, cleaning or working on the appliance.
Wear suitable working clothes, long trousers •
and solid shoes. Do not operate the appliance when
barefoot or wearing open sandals.
Use safety equipment!•
It is forbidden to move or modify any of the •
internal parts of the device.
Specic safety rules
The warnings and safety instructions must be •
followed to ensure reasonable safety and eciency
in using the spray gun. The working environment
must be free of dust, acid vapour, explosive gases and
fIammable materials. Do not use near naked ame.
Under no circumstances should the spray gun be •
pointed towards humans or animals: materials are
dispersed from the spray gun at a very high pressure.
The spray gun must only be used for paints •
and soIvents with a minimum ashpoint of 32°C.
Always read the precautions laid down by the paint
To Next Page
Loading...