9
Manual instruction
EN
The tool must be assembled correctly before use.•
Only use the tool for its designed purposes. •
In addition to the design of the tool there may •
be safety decals that must be considered and
indications about the safety equipment to use.
The prevention of accidents is dependent upon
the awareness, common sense and proper training
of everyone involved in the operation, transport,
maintenance and storage of the tool.
Never leave the tool unattended.•
Never allow children to use the tool. Children •
should be supervised to ensure that they do not
play with the tool.
Keep children and pets away. All onlookers •
should be kept at a safe distance away from the tool
when it is in use.
The user is responsible for third parties while •
working with the tool .
People who aren’t acquainted with the operating •
instructions, children, juveniles who have not yet
reached the minimum age for using this tool and
people under the inuence of alcohol, drugs or
medication are not allowed to use the tool . Local
regulations may restrict the age of the operator.
WARNING: The consumption of alcohol,
medication and drugs, plus states of
illness, fever and fatigue will aect your
ability to react. Do not use this tool in any of these
situations.
Make sure that all the protective devices (if •
present) are tted and are in good condition.
Never operate the tool with defective safety •
devices or guards (if present), or without safety
devices in place .
Inspect the entire tool to look for loose parts (e.g. •
nuts, bolts, screws, etc.) and for any damage. Check
at frequent intervals if screws and bolts are properly
tight to be sure the equipment is in safe working
condition. Repair or replace them, if necessary,
before using the machine. Serious injury to the
operator and to the bystanders could result if there’s
a damage to the tool .
While using the tool, dress properly. Do not •
wear loose clothing or jewelry that could become
caught by the tool. Wear suitable working clothes. It is
recommended that legs and feet are covered, to protect
from ying debris. Long air should be tided back.
Keep handles and grips dry, clean and free from •
oil and grease.
Use a proper protective equipment. Use •
safety glasses and safety gloves. Also use a dust
mask during pulverulent operations or if exaust
gases are present. When necessary, use also non-
slipping boots or shoes, hardhat and earplugs. If
the noise level exceeds 85 dB(A), ear protection is
obligatory.
WARNING! Use personal protective
equipment! Safety devices and the
personal protective equipment protect
your own health and the health of others and
ensure a trouble-free operation of the tool .
Do not start to use the tool if it is in an inverted •
position or it is not in the right working order.
Ensure that you have a good stand, while you •
operate with the tool. Keep proper footing and
balance at all times.
Keep work area clean. Cluttered areas invite •
injuries. Before use, all foreign bodies must be
removed from the working area, also pay attention
to foreign objects during the operation.
Do not force the tool.•
Only work in daylight or suciently good •
articial light. Never operate the tool without good
visibility.
Be careful not to drop the tool or hit it against •
obstacles.
Stay alert. Watch what you are doing.
Distraction can cause you to lose
control. Use common sense.
Electrical safety rules
ATTENTION! When using electrical tools,
the following safety instructions should
be observed to prevent the risk of electric
shock, personal injury and re. Read and observe
these instructions carefully before using the tool.
It is recommended for increased electrical •
safety to use a Residual Current Device (RCD) with
a tripping current of not more than 30 mA. Always
check your RCD every time you use it. Consult a
reliable electrician.
WARNING! The use of an RCD or other
circuit breaker unit does not release the
operator from the safety instructions
and safe working practices given in this manual.
The main voltage must correspond to the one •
marked on the technical data plate. Do not use
other sources of power.
Before inserting the plug in the main socket, •
make sure that the socket ratings are correct and
correspond to those indicated on the rating label on
To Next Page
Loading...
Need help?
General