GB-1
JACOBSEN G-PLEX III Series: DN & DP
SAFETY AND OPERATORS MANUAL
GB
1 CONTENTS
CONTENTS PAGE
2 INTRODUCTION ......................................................................................................... 2
2.2 PRODUCT IDENTIFICATION .......................................................................... 2
2.1 IMPORTANT .................................................................................................. 2
3 SAFETY INSTRUCTIONS ........................................................................................... 3
3.1 OPERATING INSTRUCTIONS ......................................................................... 3
3.2 SAFETY SIGNS .............................................................................................. 3
3.3 STARTING THE ENGINE ................................................................................. 3
3.4 DRIVING THE MACHINE ................................................................................ 3
3.5 TRANSPORTING ........................................................................................... 3
3.6 LEAVING THE DRIVING POSITION ................................................................ 4
3.7 SLOPES ........................................................................................................ 4
3.8 BLOCKED CUTTING CYLINDERS .................................................................. 4
3.9 ADJUSTMENTS, LUBRICATION AND MAINTENANCE ................................... 4
4 SPECIFICATIONS ...................................................................................................... 6
4.1 ENGINE SPECIFICATION ................................................................................ 6
4.2 MACHINE SPECIFICATION ............................................................................ 6
4.3 CUTTING UNIT .............................................................................................. 6
4.4 DIMENSIONS ................................................................................................. 6
4.5 VIBRATION LEVEL ........................................................................................ 7
4.6 SLOPES ........................................................................................................ 7
4.7 RECOMMENDED LUBRICANTS ..................................................................... 7
4.8 CUTTING PERFORMANCE ............................................................................ 7
4.9 CONFORMITY CERTIFICATES ...................................................................... 8
5 DECALS ................................................................................................................... 10
5.1 SAFETY DECALS ......................................................................................... 10
6 CONTROLS .............................................................................................................. 11
6.1 HAND CONTROLS - GASOLINE ................................................................... 11
6.1.1 HAND CONTROLS - DIESEL ......................................................................... 12
6.2 CONTROL PEDALS ...................................................................................... 13
6.3 PARKING BRAKE PEDAL .............................................................................. 13
6.4 PADDLE/FOOTSWITCH MOW/LIFT .............................................................. 13
7 OPERATION .............................................................................................................. 14
7.1 DAILY INSPECTION ...................................................................................... 14
7.2 OPERATOR PRESENCE AND SAFETY INTERLOCK SYSTEM ....................... 15
7.3 OPERATING PROCEDURE ............................................................................. 16
7.4 MOWING PROCEDURES .............................................................................. 17
8 SETUP 17
8.1 SET UP ......................................................................................................... 18
8.2 MOUNTING THE CUTTING HEADS ............................................................... 19
8.3 REEL MOTOR MOUNTING ............................................................................ 20
9 ADJUSTMENTS ........................................................................................................ 21
9.1 SEAT ADJUSTMENT LEVER ........................................................................ 21
9.2 CONTROL ARM ADJUSTMENT ................................................................... 21
9.3 BEDKNIFE ADJUSTMENT ............................................................................. 22
9.4 HEIGHT OF CUT ........................................................................................... 23
10 LUBRICATION & MAINTENANCE ............................................................................. 24
10.1 LUBRICATION & MAINTENANCE CHART .................................................... 24
10.2 LUBRICATION DIAGRAM ............................................................................. 25
10.3 HYDRAULIC PUMP BYPASS VALVE ............................................................ 26
10.4 FREE WHEELING OR TOWING UNIT .............................................................. 26
10.5 FUEL RECOMMENDATIONS - DIESEL .......................................................... 27
10.5.1 FUEL RECOMMENDATIONS - GASOLINE ..................................................... 27
10.6 AIR CLEANER - GASOLINE .......................................................................... 28
10.6.1 AIR CLEANER - DIESEL ................................................................................ 28
10.7 TIRES ........................................................................................................... 29
10.8 ENGINE ACCESS .......................................................................................... 29
10.9 ENGINE OIL LEVEL - GASOLINE .................................................................. 30
10.9.1 ENGINE OIL LEVEL - DIESEL ........................................................................ 30
10.10 BATTERY ..................................................................................................... 31
10.11 JUMP STARTING ......................................................................................... 32
10.12 CUTTING HEAD MAINTENANCE .................................................................. 32
10.13 HYDRAULIC SYSTEM .................................................................................. 33
11 GUARANTEE / SALES & SERVICE ............................................................................ 34
To Next Page
Loading...
