EasyManua.ls Logo

JAGO STAN01 - User Manual

JAGO STAN01
54 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
DE FR EN ES
Schiebetorantrieb/
M
écaniSMe d‘ouverture pour portail couliSSant/
Sliding gate operator/abridor de verjaS correderaS
Stan01
original-bedienungSanleitung/Mode d’eMploi original/
original inStruction Manual/Manual de inStruccioneS
Liebe Kundin, lieber Kunde,
danke, dass Sie sich für unser Produkt entschieden
haben. Bitte lesen Sie die Bedienungsanleitung
aufmerksam durch, bevor Sie das Produkt montieren,
anschließen oder benutzen, um Schäden durch
unsachgemäßen Gebrauch zu vermeiden. Beachten
Sie insbesondere die Sicherheitshinweise. Sollten Sie
dieses Produkt an Dritte weitergeben, muss diese
Bedienungsanleitung mit ausgehändigt werden.
chèreS clienteS, cherS clientS,
Nous vous remercions d´avoir choisi notre produit.
Nous vous prions de bien vouloir lire le mode d´emploi
attentivement avant de monter ou d´utiliser le
produit an d´éviter des dommages causés par une
utilisation non conforme. Veuillez prêter une attention particulière aux instructions de sécurité. Si
vous souhaitez donner ce produit à une tierce personne, veuillez y joindre cette notice d´utilisation.
dear cuStoMer,
Thank you for choosing our product. Please read this manual carefully before assembling or using
the product to avoid damage caused by improper use. Please pay special attention to the safety
instructions. If the product is passed on to third parties, this manual has to be passed on along
with the product.
eStiMado cliente,
Gracias por elegir nuestro producto. Para evitar daños debidos a un uso incorrecto, lea
detenidamente este manual de instrucciones antes de montar o utilizar el producto. Preste
atención a las instrucciones de seguridad. En caso de que sea transferido a terceras personas,
también deben recibir este manual de instrucciones junto a él.

Table of Contents

Questions and Answers

  • J
    jonesterriJul 25, 2025
    Why JAGO STAN01 remote transmitter does not work?
    • H
      Hannah StewartJul 25, 2025
      If the JAGO Garage Door Opener remote transmitter isn't working, it could be due to a low battery. Try replacing the battery in the transmitter. Alternatively, the transmitter code might be lost, in which case you should re-program the transmitter.
  • A
    Andres JonesAug 2, 2025
    What to do if JAGO Garage Door Opener fails to open and close and the LED display does not light up?
    • M
      Michael RamirezAug 2, 2025
      If your JAGO Garage Door Opener fails to open or close and the LED display is not lit, the power may be off. Make sure that the power is on. If the power is on, the fuse might be blown. In this case, replace the fuse.
  • L
    Lisa RiveraAug 10, 2025
    What to do if JAGO Garage Door Opener can be opened but fails to close?
    • J
      Jason CollinsAug 10, 2025
      If your JAGO Garage Door Opener opens but won't close, it might be because the infrared beam is obstructed. Remove any obstructions that you find. Also, if the infrared photocell function is enabled, but the photocell hasn't been installed, make sure the infrared photocell function is disabled.
  • C
    Caleb NolanAug 17, 2025
    Why JAGO STAN01 transmitter operating distance is too short?
    • M
      Matthew PenaAug 17, 2025
      If the operating distance of your JAGO Garage Door Opener transmitter is too short, the battery might be low. Replace the battery.

Summary

Safety Instructions

Parts List

Technical Data

Installation

Preparation of the gate

Ensure the gate is properly installed and slides smoothly before installing the operator.

Installation of the gate operator

Details on mounting the gate operator base onto a concrete pad for stability.

Installation of the rail

Steps for attaching rail elements and ensuring proper meshing with the gear.

Installation of the spring limit switch block

How to install the switch block to stop the gate accurately at open/closed positions.

Installation of the infrared sensor

Guidance on mounting the infrared sensor receiver and emitter for safety detection.

Wire Connection

Power input connection

Connecting the main power supply and ensuring the operator is properly grounded.

Infrared sensor connection

Connecting the infrared sensor receiver to the control board terminals.

Verify the opening direction

Instructions on reversing motor direction if the gate opens incorrectly.

Caution light connection

Connecting wires for the optional caution light.

Single-button switch; Three-button switch connection

How to connect single or three-button switches for gate operation.

Setting the Automatic Closing Time

Setting the Remote Control

Maintenance

Manual Operation

Troubleshooting

Environmental Protection

EC Declaration of Conformity

JAGO STAN01 Specifications

General IconGeneral
BrandJAGO
ModelSTAN01
CategoryGarage Door Opener
LanguageEnglish