JBL VP7210 - User Manual

JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A.
JBL VP7210/95DP REV H
11-11
Technical Manual
JBL VP7210/95DP
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• Frequency Response: 80 Hz - 20 kHz (±3 dB)
• Frequency Range: 50 Hz – 20 kHz (–10 dB)
• Maximum Peak Output: 132 dB SPL 1m
• Coverage Pattern: 90º x 50° rotatable waveguide
• Directivity Factor (Q): 10
• Directivity Index (DL): 10 dB
TRANSDUCER SECTION:
• Cabinet: Enclosure (Not for Sale)
• Grille: 362983-001
• Low Frequency Driver: 2261FF, 254mm (10 in) dia., 76mm (3
in) Dual Coil neodymium Differential
Drive, Direct Cooled
• Bandpass Nominal Impedance: 2 x 2 ohms
• High Frequency Driver: 2452H-SL, 100mm (4 in) titanium
damped diaphragm, 1.5 in exit,
• Bandpass Nominal Impedance: 8 Ohms
SYSTEM:
• DPC1 Internal Amplification 1750W Peak, 875W Continuous
Output (at nominal load):
• DPC1 Output: 750 LF / 125 HF Watts (Continuous
IEC shaped pink noise into rated load
impedance)
• DPC1 Output Section: LF: Dual Bridge Technology, Class D
HF: Bridged Class D
SYSTEM CONT’D:
• Audio Input Connector: XLR with loop-through
• User Controls: 80 Hz Subwoofer High Pass Filter.
Enable / Disable 0-16 dB input
Attenuator w/ 32 precision 0.5 dB steps
• Signal Processing: DSP based, resident in Input Module
• System Management: DSP based limiters for mechanical
and thermal protection
• AC Power Operating Range: 90-132 VAC / 216-264 VAC, 50/60 Hz
• AC Line Voltage: 50/60 Hz, Auto-Detect; 120V/240V
(-15%, +10%)
• AC Input Connector: Neutrik PowerCon (NAC 3MPA)
• AC Look-thru: Neutrik PowerCon (NAC 3MPB)
• AC Current Requirement: 6A/system @ 120V, 3A/system @ 240V
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 100mV Input,, 20 Hz to 20 kHz
B. L.F. Aural Sweep Test: 4.0V Input, 20 Hz to 1.2 kHz
C. H.F. Aural Sweep Test: 2.5V Input, 300 Hz to 20 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions: 521 x 293 x 303 mm
(Height x Width x Depth) 20.5 x 11.5 x 11.9 in
• Net Weight: 40.5 lb (18.4 kg)
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
Owners Manual
363642-001
Package, Microfoam (4)
49790P
Carton
363643-001
Filler (2)
363641-001
PKG, Microfoam (4)
49790P
Tape (8)
65012-01
Power Cord Assy Pack
355040 -002
PACKAGE WIRING DIAGRAM
SCHEMATIC
Driver, Low Frequency
2261FF
(354964-003X)
Cone Repl
C2X2R2261
Wire Harness
363640-001
Driver, High Frequency
2452H-SL
(352328-003X)
Diaph Repl
D8R2452-SL
Yel/Blk
Yel
Blu/Blk
Grn
Blu
Grn/Blu

Summary

Product Specifications

Acoustic & Electrical Specifications

Details frequency response, output, coverage pattern, and driver parameters.

Transducer Section Details

Describes cabinet, grille, and specifications for low and high frequency drivers.

System & Power Specifications

Covers system controls, signal processing, power operating range, and connectors.

Aural Sweep Test Specifications

Lists input levels for system, LF, and HF aural sweep testing.

Physical & Weight Specifications

Provides enclosure dimensions and net weight of the unit.

Wiring Diagram Overview

Illustrates internal wiring connections for low and high frequency drivers.

Package Contents

Package Item List

Lists all components included in the product's packaging.

System Schematics

System Schematic and Housing Detail

Presents a system schematic and housing detail with connection point identification.

Component Exploded View

Product Component Breakdown

Detailed exploded view showing all parts and hardware for assembly.

Amplifier Assembly Details

Amplifier Module Components

Identifies key components of the amplifier assembly, including PCBs and labels.

JBL VP7210 Specifications

General

Nominal Impedance	8 Ohms
Weight	22.7kg (50 lbs)
Crossover Frequency	1.8 kHz
Input Connectors	Neutrik NL4MP Speakon connectors
Type	Two-way
Enclosure Material	plywood
LF Driver	12" (300mm) woofer