To Next PageTo Next PageHow to fix a Jensen VM9726BT Car Receiver that won't turn on?
If your Jensen Car Receiver unit will not power on, there might be a blown fuse. Try installing a new radio fuse or car battery fuse with the correct rating. If that doesn't work, the system may have experienced an illegal operation. In this case, press the RESET button located over the rotary encoder on the front panel.
Why is the audio so low on my Jensen Car Receiver?
If you're experiencing no or low audio output from your Jensen Car Receiver, start by checking the wiring and correcting any improper audio output connections. Make sure the volume isn't set too low; increase it if necessary. Review the wiring diagram and check the “MUTE” connection. Damaged speakers can also cause this issue, so consider replacing them. Additionally, check if the volume balance is heavily biased and adjust the channel balance to the center position. Finally, ensure that the speaker wiring is not in contact with any metal parts of the car; insulate all speaker wiring connections if needed.
What to do if my Jensen Car Receiver image is flashing?
If the image on your Jensen Car Receiver is flashing or showing interference, the DVD might not be compatible with the current TV system settings. Try changing the setup to accommodate the disc. Also, check the video signal connections to ensure they are properly wired.
Why is my Jensen VM9726BT Car Receiver sound quality so bad?
If your Jensen Car Receiver has poor sound quality or distortion, the problem may be due to a pirated disc. Try using an original copy. Also, make sure the speaker power rating is compatible with the unit, and check the speaker contact to ensure it is not shorted.
Why is there no image on my Jensen VM9726BT?
If your Jensen Car Receiver is showing no image, check the connection to the parking brake wire and make sure it is correctly wired. Also, ensure that the parking brake is engaged by stopping the vehicle in a safe place and applying the parking brake.
Why is my Jensen VM9726BT having weak station searching?
If the station searching on your Jensen Car Receiver is weak, the auto antenna may not be fully extended or properly connected. Connect the auto antenna control cable properly. Also, check if the LOCAL function is activated and turn it off if it is.
What to do if I can't insert a disc into my Jensen VM9726BT?
If you cannot insert a disc into your Jensen Car Receiver, it is possible that there is already a disc inside the unit. Eject the current disc and then try inserting the new one.
Why is the image on my Jensen VM9726BT blurred?
If the image on your Jensen Car Receiver is blurred, distorted, or dark, the disc you are using might be an illegally copied one. Try using an original disc.
How to fix prolonged image on Jensen Car Receiver?
If your Jensen Car Receiver displays a prolonged image or an improper height/width ratio, the aspect ratio setup might be incorrect. Use the correct aspect ratio setting to resolve this issue.
Why won't my Jensen Car Receiver play the disc?
If a disc does not play back on your Jensen Car Receiver, the disc may be warped, scratched, dirty, or wet. Use a disc in good condition or clean the disc with a soft cloth. The laser pickup might also be dirty, so clean it with a cleaning disc. Ensure you are using a compatible disc with the proper region code, and that the disc rating does not exceed the Parental Lock rating limit. Also, make sure the disc is inserted with the label side up.
General| Touchscreen | Yes |
|---|---|
| Display Resolution | 800 x 480 |
| Bluetooth | Yes |
| USB Port | Yes |
| Audio Output | 4 x 50 Watts |
| Radio Tuner | AM/FM |
| Rear Camera Input | Yes |
| DVD Player | Yes |
| SD Card Slot | Yes |
| Peak Output | 50 Watts |
| Navigation | No |
| Steering Wheel Control Compatible | Yes |
| AUX Input | Yes |
| CD Player | Yes |
| GPS Navigation | No |
| Backup Camera Input | Yes |
| Display Size | 6.2 inches |
| Compatible Formats | MP3, WMA, JPEG |
| Preamp Outputs | Front, Rear, Subwoofer |
