How to fix a Jensen Car Receiver with no power?
If your Jensen Car Receiver is not getting power, ensure the vehicle’s ignition is switched to “ACC” if the power supply is correctly connected to the vehicle accessory terminal. Also, check the fuse and replace it if it's blown.
Why is there no sound coming from my Jensen Car Receiver?
If your Jensen Car Receiver has no sound, first, make sure the volume isn't too low by adjusting it to a suitable level. Then, check the fader settings by pressing the AUDIO button to access the menu and adjust them as needed. Finally, inspect the wiring connections to ensure they are properly connected.
How do I stop my Jensen Car Receiver from turning on and tuning to the weather band automatically?
If your Jensen Car Receiver automatically turns on (ignition on) and tunes to WB (Weather Band), you can prevent this by setting the Alert Pwr setting to “OFF” in the System menu.
What to do if my Jensen VR209 Car Receiver won't load or eject a disc?
If your Jensen Car Receiver's disc cannot be loaded or ejected, consider these potential causes and solutions: 1. If there's already a disc inside, remove it before inserting a new one. 2. Ensure you're inserting the disc correctly, with the label facing upward. 3. If the disc is dirty, clean it, or try a new disc. 4. If the vehicle's internal temperature is too high, wait for it to return to normal. 5. If condensation is the issue, leave the player off for about an hour before trying again.
What to do if the operation keys on my Jensen Car Receiver do not work?
If your Jensen Car Receiver's operation keys are not working, press the RESET button. This will help if the built-in microcomputer isn't operating correctly due to noise.
Why does the sound skip on my Jensen VR209 Car Receiver?
If the sound skips on your Jensen Car Receiver, adjust the installation angle to be less than 30 degrees. Also, clean the disc and try playing it again, or use a new disc if the current one is defective.
Why can't my Jensen VR209 Car Receiver tune to radio stations?
If your Jensen Car Receiver cannot tune to a radio station or auto-seek isn't working, make sure the antenna cable is firmly inserted. If the signals are too weak, select a station manually.
How do I stop my Jensen VR209 from automatically switching to the weather band?
CD Specifications| signal to noise ratio | > 60 dB |
|---|---|
| channel separation | More than 50 dB |
| frequency response | 40 Hz - 18 kHz |
FM Radio Specifications| frequency range (USA) | 87.5 to 107.9 MHz |
|---|---|
| frequency range (Europe) | 87.5 to 108 MHz |
| sensitivity (S/N=30dB) | 4 µV |
AM/MW Specifications| frequency range (USA) | 530-1710 KHz |
|---|---|
| frequency range (Europe) | 522-1620 KHz |
| sensitivity (S/N=20dB) | 36 dB |
General Specifications| operating voltage | DC 12 Volts |
|---|---|
| speaker impedance | 4-8 ohms per channel |
| power output | 50W x 4 |
Keep volume low to remain aware of road and traffic conditions.
Do not expose the product to water to prevent damage.
Avoid direct sunlight to prevent overheating inside the vehicle.
Designed for 12-volt DC negative ground battery systems.
Caution regarding visible/invisible laser beam exposure.
Reduce risk by using only recommended accessories.
Specifies dashboard opening dimensions for 2-DIN installation.
Connect to a 12-volt power source that is always live.
Connect to existing radio accessory fuse or switched power source.
Access NOAA weather channels and configure weather alerts.
Manage playback of CDs, MP3s, and WMAs (play, pause, skip, etc.).
Manage playback of files from USB devices (play, pause, skip, etc.).
Store Sirius stations in memory for quick access.
Set and change the parental control access code.
Restrict access to specific Sirius channels.
Accessing channels that require a parental code.
Remove channel lock restrictions by entering the code.
Manage iPod song playback functions (play, pause, skip, repeat).
To Next Page