EasyManua.ls Logo

Jet HVBS-10-DMW - User Manual

Jet HVBS-10-DMW
40 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
Operating Instructions and Parts Manual
Portable Dual Mitering Band Saws
Models HVBS-8-DMW, HVBS-10-DMW, HVBS-10-DMWC
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-424460
Ph.: 800-274-6848 Edition 1 12/2016
www.jettools.com Copyright © 2016 JET
Model HVBS-10-DMWC shown

Table of Contents

Questions and Answers

  • L
    Lori PearsonAug 16, 2025
    Why is my Jet HVBS-10-DMW blade breaking excessively?
    • V
      Valerie HillAug 16, 2025
      Excessive blade breakage in your Jet Saw can occur for several reasons. It may be due to the material being loose in the vise, so ensure you clamp the work securely. Other causes include incorrect speed or feed (check machinery handbook for appropriate settings), teeth being too coarse for the material (consult the machinery handbook for the recommended blade type), incorrect blade tension (adjust until the blade doesn't slip), the blade contacting the workpiece before starting the saw (start the motor first), the blade rubbing on the wheel shoulder (adjust blade tracking), misaligned guides (adjust them), or cracking at the weld (requires a longer annealing cycle).
  • J
    jamesmontgomeryAug 19, 2025
    What to do if my Jet Saw is making bad (out-of-square) cuts?
    • J
      Jamie ByrdSep 12, 2025
      If your Jet Saw is producing out-of-square cuts, several factors could be responsible. Ensure the workpiece is square with the blade by adjusting the vise and clamping the work tightly. Other potential causes include feed pressure being too fast (decrease it), guide bearings not adjusted properly (adjust clearance to 0.001-0.002 inch), inadequate blade tension (gradually increase it), the span between blade guides being too wide (move the guide bar closer), a dull blade (replace it), incorrect blade speed (check the pulley position), a loose blade guide assembly (tighten it), a loose blade guide bearing assembly (tighten it), the blade track being too far from wheel shoulders (adjust blade tracking), or worn guide bearings (replace them).
  • R
    Rachel TownsendAug 22, 2025
    Why does my Jet HVBS-10-DMW Saw motor running too hot?
    • W
      wdeanAug 22, 2025
      If the motor of your Jet Saw is running too hot, several factors could be the cause. These include blade tension being too high (reduce it), drive belt tension being too high (reduce it), the blade being too coarse for the workpiece, especially with tubular stock (use a blade with a fine tooth pitch), the blade being too fine for the workpiece, especially with heavier, soft material (use a blade with a coarse tooth pitch), or insufficient gearbox lubrication (check the gearbox oil).
  • C
    Cory StokesAug 26, 2025
    What to do if my Jet HVBS-10-DMW blade dulls prematurely?
    • S
      Steven OliverAug 26, 2025
      If your Jet Saw blade is dulling prematurely, consider the following: the blade teeth may be too coarse (use a finer tooth blade), the blade speed may be too high (try a lower speed), the feed pressure may be inadequate (decrease spring tension), there may be hard spots or scale on the workpiece (increase feed pressure for hard spots; reduce speed and increase feed pressure for scale), work hardening of the material may be occurring (increase feed pressure by reducing spring tension), blade tension may be insufficient (increase it), or you may be operating the saw without pressure on the workpiece (avoid running the blade at idle).
  • M
    Matthew MillerAug 28, 2025
    How to fix bad (rough) cuts with my Jet HVBS-10-DMW?
    • B
      Brian ProctorAug 28, 2025
      If your Jet Saw is producing rough cuts, it could be due to the blade speed being too high for the feed pressure. Try reducing both. Another cause may be that the blade is too coarse, in which case you should replace it with a finer blade.
  • D
    Dorothy PowellAug 31, 2025
    Why is my Jet HVBS-10-DMW blade twisting?
    • C
      Christine PetersAug 31, 2025
      If the blade on your Jet Saw is twisting, it could be binding in the cut. Decrease the feed pressure. Alternatively, the blade tension may be too high, so decrease the tension on the blade.
  • G
    Glenn TuckerSep 3, 2025
    What causes unusual wear on the side or back of my Jet Saw blade?
    • B
      Brianna YuSep 3, 2025
      Unusual wear on the side or back of your Jet Saw blade can be caused by worn blade guides. Replace the blade guides. It may also be caused by blade guide bearings not being adjusted, so adjust them accordingly. Another possibility is that the blade guide bearing bracket is loose, so tighten it.
  • J
    janetwallerSep 6, 2025
    What causes teeth missing/ripped from blade of my Jet HVBS-10-DMW?
    • D
      Dr. Karen BennettSep 6, 2025
      Missing or ripped teeth on your Jet Saw blade can occur if the blade tooth pitch is too coarse for the workpiece, so use a blade with a finer tooth pitch. It could also be from the feed being too slow or too fast, in which case you should increase feed pressure and/or blade speed. Workpiece vibration can also cause this issue, so clamp the workpiece securely. Finally, gullets loading up with chips can contribute, so use a blade with a coarser tooth pitch, reduce feed pressure, and brush the blade to remove chips.
  • M
    Melinda MoralesSep 9, 2025
    What to do if there is no coolant flow in my Jet HVBS-10-DMW Saw?
    • R
      rrobinsonSep 9, 2025
      If there is no coolant flow in your Jet Saw, the pump motor may be burned out, requiring replacement. Alternatively, the screen/filter on the pump may be clogged, so clean it. It's also possible that the impeller is loose, so tighten it. Lastly, the coolant level may be too low, so add coolant to the reservoir.
  • A
    Amanda RichSep 12, 2025
    Why does my Jet HVBS-10-DMW Saw have excessive noise or vibration?
    • T
      Tyler SotoSep 12, 2025
      Excessive noise or vibration in your Jet Saw can be caused by the belt being too tight. Try resetting the belt tension.

Jet HVBS-10-DMW Specifications

General IconGeneral
BrandJet
ModelHVBS-10-DMW
CategorySaw
LanguageEnglish

Related product manuals