Jet JDP-17 - User Manual

Questions and Answers

J
Jose HenryAug 16, 2025
Why my Jet Drill press does not come up to speed?
- C
  Crystal MartinAug 16, 2025
  If your Jet Drill press does not come up to speed, several factors could be responsible. An extension cord that is too light or too long can cause this, so replace it with an adequate size and length cord. Low current could also be the issue, so contact a qualified electrician. Additionally, a motor or spindle pulley might be out of balance, so contact JET technical service. Finally, there might be a motor malfunction, so have the motor tested by a qualified service center and repair or replace it as necessary.
J
Jeanne WolfeAug 19, 2025
Why Jet Drill chuck won’t remain in spindle?
- J
  Joshua SmallAug 19, 2025
  If the chuck won’t remain in the spindle of your Jet Drill, it's likely due to grease or dirt on the spindle or chuck tapers. Clean the tapers thoroughly.
T
Toni WilsonAug 21, 2025
Why does my Jet JDP-17 Drill motor stall?
- E
  Erin BellAug 21, 2025
  If the Jet Drill press motor stalls, it could be due to several reasons. You might be overfeeding the bit, so try lowering the bit more slowly. A dull bit can also cause the motor to stall, so sharpen or replace the bit. In some cases, the motor might not be reaching running speed, or there could be a motor malfunction, in which case you should have the motor tested by a qualified service center.
Y
ymoraAug 25, 2025
How to fix a Jet JDP-17 Drill press that will not start (power light is OFF)?
- C
  Catherine BlackburnAug 26, 2025
  If your Jet Drill press won't start and the power light is off, the issue could stem from a few things. First, make sure the drill is properly connected to a power source by checking the plug connection. If it's connected, a fuse might be blown, or the circuit breaker tripped, so replace the fuse or reset the circuit breaker. Finally, inspect the cord for any damage and replace it if necessary.
N
Natalie LynchAug 27, 2025
Why is my Jet Drill making a noisy operation?
- A
  Amanda WilsonAug 27, 2025
  If your Jet Drill press is making excessive noise, start by tightening any loose parts and ensuring the drill press sits evenly on a level floor. Secure the drill press to the floor or a plywood base to reduce vibration. Also, a dry spindle can cause noise, so lubricate it. Check for loose pulleys or belts and make any needed corrections, verifying that the belts are properly tensioned. Finally, inspect the motor for noisy motor bearings or a loose motor fan.
A
Amanda GriffinAug 31, 2025
What to do if Jet JDP-17 Drill press will not start (power light is ON)?
- K
  Kyle SmithAug 31, 2025
  If your Jet Drill press won't start but the power light is on, the problem might be that the safety key has been removed. Install the safety key. If the safety key is installed, there may be a switch malfunction. In this case, have the switch tested and replaced if needed.
T
Tyrone JonesSep 2, 2025
Why does my Jet JDP-17 Drill or tool heats up or burns work piece?
- G
  guerrerokatieSep 2, 2025
  If your Jet Drill or tool heats up or burns the work piece, it could be due to excessive speed, so reduce the speed. Another possible cause is that chips are not clearing from the hole or bit; retract the drill bit frequently to remove chips. A dull drill bit can also cause overheating, so resharpen or replace the drill bit. Lastly, feeding the bit too slowly can cause this issue, so increase the feed rate.
W
wolfedonnaSep 6, 2025
Why does the Jet JDP-17 Drill bit wanders?
- N
  Nathaniel ChavezSep 6, 2025
  If the Jet Drill bit wanders, it might be because the bit was sharpened incorrectly, so resharpen the bit correctly. A bent drill bit can also cause wandering, so replace the bit. Finally, check if the bit or chuck is not installed properly and reinstall the chuck or bit.
K
Katie MontgomerySep 9, 2025
Why does the Jet JDP-17 bit binds in work piece?
- M
  meganmorganSep 9, 2025
  If the Jet Drill bit binds in the work piece, it could be that the work piece is pinching the bit, so support or clamp the work piece. An excessive feed rate can also cause binding, so lower the bit more slowly into the workpiece. Additionally, the speed setting might be too low for the workpiece, so consult the chart for recommended speed. Finally, check if the chuck jaws are not tight and tighten them.
A
Alex MaySep 12, 2025
How to prevent wood splinters on underside of work piece with Jet JDP-17?
- M
  Michelle BurgessSep 12, 2025
  Wood splinters on the underside of your work piece when using the Jet Drill can be prevented by placing a scrap board beneath the work piece to prevent splintering. This is likely happening because no backing board was used.