30 Technical Bulletin—TC-9102
Table 5: TC-9102 Controller Ordering Codes
Ordering Code Hardware
Configuration
Code (used in
EuroPRO)
Outputs Set Point
Range
TC-91a2-b220 TC-91x2-x220 2 x 0 to 10 VDC 0 to 10 VDC Fan Control 12 -28°C
TC-91a2-b225 TC-91x2-x220 2 x 0 to 10 VDC 0 to 10 VDC Fan Control +/-3 K
TC-91a2-b440 TC-91x2-x330 2 x DAT 0 to 10 VDC Fan Control 12 -28°C
TC-91a2-b445 TC-91x2-x330 2 x DAT 0 to 10 VDC Fan Control +/-3 K
TC-91a2-b550 TC-91x2-x330 2 x PAT 0 to 10 VDC Fan Control 12 -28°C
TC-91a2-b555 TC-91x2-x330 2 x PAT 0 to 10 VDC Fan Control +/-3 K
TC-91a2-b660 TC-91x2-x330 2 x 2 Stage On/Off 0 to 10 VDC Fan Control 12 -28°C
TC-91a2-b655 TC-91x2-x330 2 x 2 Stage On/Off 0 to 10 VDC Fan Control +/-3 K
TC-91a2-b221 TC-91x2-x221 2 x 0 to 10 VDC On/Off Fan 12-28°C
TC-91a2-b226 TC-91x2-x221 2 x 0 to 10 VDC On/Off Fan +/-3 K
TC-91a2-b441 TC-91x2-x331 2 x DAT On/Off Fan 12-28°C
TC-91a2-b446 TC-91x2-x331 2 x DAT On/Off Fan +/-3 K
TC-91a2-b551 TC-91x2-x331 2 x PAT On/Off Fan 12-28°C
TC-91a2-b556 TC-91x2-x331 2 x PAT On/Off Fan +/-3 K
TC-91a2-b661 TC-91x2-x331 2 x 2 Stage On/Off On/Off Fan 12-28°C
TC-91a2-b666 TC-91x2-x331 2 x 2 Stage On/Off On/Off Fan +/-3 K
TC-91a2-b222 TC-91x2-x222 2 x 0 to 10 VDC 3-Speed Fan 12-28°C
TC-91a2-b227 TC-91x2-x222 2 x 0 to 10 VDC 3-Speed Fan +/-3 K
TC-91a2-b442 TC-91x2-x332 2 x DAT 3-Speed Fan 12-28°C
TC-91a2-b447 TC-91x2-x332 2 x DAT 3-Speed Fan +/-3 K
TC-91a2-b552 TC-91x2-x332 2 x PAT 3-Speed Fan 12-28°C
TC-91a2-b557 TC-91x2-x332 2 x PAT 3-Speed Fan +/-3 K
TC-91a2-b662 TC-91x2-x332 2 x 2 Stage On/Off 3-Speed Fan 12-28°C
TC-91a2-b667 TC-91x2-x332 2 x 2 Stage On/Off 3-Speed Fan +/-3 K
Controller for remote set point: a = 0, with integrated set point: a = 1
Controller with standard terminals: b = 0, with separable terminals: b = 1
Notes: 1. Ordering codes must be used in orders to the Lomagna factory.
2. The Hardware Configuration Code is shown in the EuroPRO Configuration Tool to indicate the basic
hardware configuration of the controller which is being commissioned. The software configuration of
the controller, as indicated by the Ordering Code, may be changed in EuroPRO to any other
software configuration with the same hardware configuration. For example, TC-91a2-b442 could be
changed to TC-91a2-b552 because both have the same hardware configuration, TC-91x2-x332.
3. Modules with PWM control signal outputs have been discontinued. Contact your local Johnson
Controls office for details of replacement controllers.
Ordering
Codes
To Next Page
Loading...
