What to do if my Johnson Controls YORK YWHJZH009BAMXAFX Air Conditioner unit can't be started?
If your Johnson Controls Air Conditioner unit cannot be started, make sure to check the power supply and connections. The issue might be due to a power cut off, a loose power plug, a tripped circuit protection device, voltage issues, or an incorrectly used timer.
Why is the cooling/heating effect poor on my Johnson Controls Air Conditioner?
If you're experiencing poor cooling or heating with your Johnson Controls Air Conditioner, adjust the temperature settings and check for any blockages in the inlet or outlet. Also, ensure that the filter is clean, windows and doors are closed, the fan speed is appropriately set, and there are no heat sources in the room.
What to do if there is water leakage from the indoor unit of my Johnson Controls YORK YWHJZH009BAMXAFX Air Conditioner?
If you notice water leakage from the indoor unit of your Johnson Controls Air Conditioner, it could be due to high humidity, overflowing condensing water, or a loose drain hose. Try to address the high humidity or secure the drain hose.
Why is the remote controller not available for my Johnson Controls Air Conditioner?
If your Johnson Controls Air Conditioner remote controller is not working, check the condition of the batteries and replace them if necessary. Also, check for any magnetic or electrical interference near the unit that may be affecting the controller's operation.
Why is there moisture on the air outlet of my Johnson Controls YORK YWHJZH009BAMXAFX Air Conditioner?
If you see moisture on the air outlet of your Johnson Controls Air Conditioner, it is expected if the unit operates at high humidity for a long time. Ensure the environment is within normal humidity levels.
Why is there water leakage from the outdoor unit of my Johnson Controls YORK YWHJZH009BAMXAFX Air Conditioner?
If you observe water leakage from the outdoor unit of your Johnson Controls Air Conditioner, it is typically due to water condensate generated around the pipes and connection joints during cooling operation, defrosting operation, or heating operation. Monitor the operation conditions.
What does F1 error mean on Johnson Controls YORK YWHJZH009BAMXAFX Air Conditioner?
If you encounter a 'F1' error, indicating a malfunction of the indoor ambient temperature sensor on your Johnson Controls Air Conditioner, check if the indoor room temperature sensor is connected properly and secure the connections to the sensor.
What does F2 error mean on Johnson Controls YORK YWHJZH009BAMXAFX Air Conditioner?
If you encounter a 'F2' error, indicating a malfunction of the evaporator temperature sensor on your Johnson Controls Air Conditioner, check if the evaporator temperature sensor is connected properly and secure the connections to the sensor.
What does H6 error mean on Johnson Controls YORK YWHJZH009BAMXAFX Air Conditioner?
If you encounter a 'H6' error, indicating an indoor fan block on your Johnson Controls Air Conditioner, check if the terminal of the indoor motor is connected properly. If disabled, consider replacing the fan motor or the indoor board.
What does C5 error mean on Johnson Controls YORK YWHJZH009BAMXAFX Air Conditioner?
If you encounter a 'C5' error, indicating a malfunction of connector jumper on your Johnson Controls Air Conditioner, check if the connector jumper contacts properly. If the PCB is to be replaced, please take off the old for the new PCB.
General| Model Number | YWHJZH009BAMXAFX |
|---|---|
| Category | Air Conditioner |
| Operating Voltage | 220-240V |
| Cooling Capacity | 9000 BTU/h |
| Operating Frequency | 50Hz |
Covers warnings about wet hands, cord handling, socket usage, and cleaning procedures.
Focuses on circuit protection, voltage, and preventing electrical hazards like fire.
Addresses earthing, maintenance power-off, temperature settings, and environmental considerations.
Details restrictions on cord damage, airflow direction, and health impacts of usage.
Identifies key components of the indoor air conditioning unit.
Identifies key components of the outdoor air conditioning unit.
Details the operation of ON/OFF, FAN, MODE, and TEMP buttons on the remote.
Explains the functionality of CLOCK, LIGHT, TURBO, X-FAN, and QUIET buttons.
Covers setting the air swing direction and timer functions (ON/OFF).
Describes how to activate and manage different sleep modes for comfort.
Details the process for customizing sleep temperature curves (DIY).
Provides guides for general operation and explains special features like X-FAN, AUTO RUN, and TURBO.
Explains features like keyboard lock, temperature units, energy saving, and quiet mode.
Instructions for changing remote control batteries and important usage notices.
Instructions for operating the unit using the manual switch when the remote is unavailable.
Step-by-step guide for cleaning the front panel and air filters.
Covers checks before use and routine maintenance after operation.
Addresses problems like the unit not operating and unusual odours.
Explains common noises like water flowing and mist emission during operation.
Covers issues related to unit startup, cooling/heating effectiveness, and remote control availability.
Details causes and solutions for water leakage and indoor unit noise.
Addresses issues with indoor unit airflow and specific malfunction codes.
Identifies critical situations that require immediate shutdown and professional service.
Explains the principles of cooling, heating, and the defrosting process.
Details anti-cold air functions and rest heat blow operations.
Provides operating temperature ranges and tips for energy saving.
Discusses the impact of relative humidity on condensate formation.
General warnings and precautions for unit installation by authorized personnel.
Guidelines for selecting appropriate locations for unit installation.
Specific placement instructions for indoor and outdoor units.
Safety measures related to electrical connections during installation.
Details on wiring, air switch capacity, and proper earthing procedures.
Steps for installing the mounting plate and drilling the piping hole.
Instructions for connecting and routing the drain hose for condensate removal.
Procedure for connecting the electric wires between indoor and outdoor units.
Guide to routing piping from the unit and connecting the flare nuts.
Covers wiring, air purging, and leakage testing for the outdoor unit.
Instructions for installing the drain connector and hose for outdoor unit condensate.
A checklist of items to verify after the unit has been installed.
Steps for conducting the initial operation test of the air conditioner.
Guidance on how to install the healthy filter onto the air filter.
Instructions for cleaning the filter and information on its service life.
Specifies the maximum and minimum lengths for refrigerant connection pipes.
Methods for calculating additional refrigerant oil and charge amounts for extended pipes.
Details recommended additional refrigerant charging amounts based on pipe diameter.
To Next Page