Need help?Do you have a question about the Jonsered FR2211R and is the answer not in the manual?
General| Engine Type | Petrol |
|---|---|
| Cutting Width | 94 cm |
| Weight | 229 kg |
| Engine Manufacturer | Briggs & Stratton |
| Drive System | Rear-wheel drive |
| Self-Propelled | Yes |
| Cutting Height | 25 - 75 mm |
| Mulching Capability | Yes |
| Side Discharge | No |
| Rear Bag | Yes |
| Cutting Height Adjustment | Central |
| Cutting Method | Rear discharge |
| Fuel Tank Capacity | 1.5 l |
Check road traffic regulations before driving on public roads and use securing devices for transport.
Towing a hydrostatic transmission machine requires caution to avoid damage, disengage power transmission.
Machine is designed for cutting grass on lawns; use contrary to intent is prohibited.
Jonsered products sold through servicing dealers for best support and service.
Location of machine and engine serial numbers for identification and ordering parts.
Steps for pre-delivery inspection and preparation before the machine is handed over to the customer.
Initial maintenance required after the first 5 hours of operation, such as changing engine oil.
Explains various symbols used on the machine and in the operator's manual for safety and operation.
General safety precautions and warnings for operating the machine.
Recommends checking insurance coverage for the Rider, including third party, fire, damage, theft, and liability.
Advises reading and understanding all instructions before operation and learning controls for quick stopping.
Provides critical safety guidance for operating the machine on slopes to prevent accidents and overturning.
Warns about the risks associated with children near the machine and provides safety measures.
Safety procedures to follow before performing any maintenance or adjustments on the machine.
Guidelines for safely transporting the machine, including securing it and following road regulations.
Identifies and locates all the main controls on the machine for user reference.
Congratulates the customer and introduces the Jonsered Frontrider models covered in the manual.
Explains how to apply and release the parking brake on specific models.
Describes the function of the clutch pedal and brake pedal for FR 2211 R/M models.
Details the throttle and choke controls for engine speed adjustment and cold starting.
Explains the choke lever for cold starting and speed limiter pedals for speed regulation.
Describes the cutting unit, its lifting lever, and cutting height adjustment.
Instructions on how to adjust the operator's seat for comfort and ergonomics.
Provides instructions and safety precautions for refuelling the machine's fuel tank.
Explains the function of the release control for moving the machine with the engine off.
Important checks and procedures to perform before starting the engine.
Step-by-step guide on how to start the engine, including clutch and cutting unit engagement.
Instructions and precautions for jump-starting the engine when the battery is weak.
Detailed steps for safely connecting jump leads for emergency starting.
How to release the parking brake, select gears, use hydrostatic pedals, and set cutting height.
Procedure for safely stopping the engine after operation.
Advice on mowing techniques for optimal results, including obstacle avoidance and grass conditions.
Specific instructions for starting the machine on a slope with a manual gearbox.
A detailed schedule outlining daily and interval-based maintenance tasks for the machine.
Instructions on how to clean the machine after use, including warnings about high-pressure washers.
Steps for removing the engine cover and fenders for access to internal components.
Guidance on checking the muffler for completeness and secure mounting.
How to check and adjust the steering wires to maintain proper steering alignment.
Procedures for checking and adjusting the brake system on specific models.
Specific instructions for adjusting the brake on FR 2213 MA, FR 2216 A, and FR 2216 A2 models.
How to adjust the throttle wire for proper engine response and maximum RPM.
Steps to adjust the choke wire for easier starting and correct mixture.
Step-by-step guide for replacing the air filter on specific Jonsered models.
Detailed instructions for replacing the air filter cartridge on the FR 2216A2 model.
Instructions for replacing the fuel filter at specified intervals or when clogged.
How to check and clean the air filter for the fuel pump.
Specifies the correct tyre pressure for optimal performance and cutting results.
Guidance on checking and maintaining the battery acid level, with safety warnings.
Information about the engine's electronic ignition system and spark plug maintenance.
Step-by-step instructions for removing, checking, and replacing the spark plug.
Location and type of the main fuse, and instructions for replacement.
How to inspect the machine's safety interlock systems to ensure they are functioning correctly.
How to clean and inspect the engine's air intake grille for obstructions.
How to check and adjust the cutting unit's ground pressure for optimal cutting.
Steps to check the cutting unit's parallelism for even mowing.
Instructions on how to adjust the cutting unit's parallelism using stay nuts.
How to place the cutting unit in a service position for easier cleaning and maintenance access.
Detailed steps for raising and locking the cutting unit into the vertical service position.
How to check the cutting blades for damage, sharpness, and secure attachment.
Steps to return the cutting unit from the service position back to normal mowing operation.
Instructions on how to remove the mulching plug to switch between mulching and rear ejection.
How to check the engine oil level when the machine is horizontal and switched off.
Procedures for changing the engine oil, including intervals and oil quantity.
Instructions for replacing the oil filter on the FR 2216A2 model.
How to check and refill the transmission oil on specific models.
Instructions for lubricating the belt adjuster using a grease gun.
How to lubricate the front wheel bearings on FR 2211 R and FR 2211 M models.
Guidance on lubricating various joints, bearings, and wires with appropriate greases and oils.
A guide to identifying and resolving common problems encountered with the machine.
Instructions for preparing the machine for long-term storage, including fuel management and cleaning.
Information about a protective cover available for the machine during storage or transport.
Advice on performing service during the low season and ordering spare parts.
Provides detailed physical dimensions and weight specifications for the machine.
Details engine brand, model, power, displacement, fuel, and oil requirements.
Specifies noise emission levels and the cutting width of the machine.
Reports vibration levels measured on the steering wheel.
Technical details on the transmission, cutting unit type, heights, and blade length.
Declares conformity with EU directives regarding machinery, EMC, and noise emissions.
To Next Page