EasyManuals Logo

JUKI LU-1511N-7 User Manual

JUKI LU-1511N-7
80 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #17 background imageLoading...
Page #17 background image
– 13 –
Adjustment Procedures Results of Improper Adjustment
Stitch skipping or thread
breakage will result.
Loose stitches will result.
1) Standard of the lowest dead point of the needle bar
1. Set the stitch dial to “0”.
2. Turn the handwheel to bring needle bar 1 to the lowest dead
point of its stroke.
3. Loosen the setscrew in the face plate to remove the face plate.
4. Loosen clamping screw 2 in the needle bar holder. At this
time, loosen the screw to such an extent that needle bar 1
moves up and down by hand since needle bar 1 drops if the
screw is fully loosened.
5. Adjust the distance from the lower end of needle bar frame to
the lower end of the needle bar to dimension A. Then tighten
clamping screw 2 in the needle bar holder. (For LU-1510N-7,
there is an engraved marker line in needle bar 1.)
2) Needle-to-blade point of hook timing
1. Set the stitch dial to “0”.
2. Loosen two setcrews 3 in the screw gear (large).
3. Turn the handwheel and when dimensions B and C are
approximately obtained, loosen setscrew A 4 and setscrew B
8 in the hook shaft driving saddle. Then move the hook driving
shaft saddle to the right or left to adjust the cearance between
needle 5 and blade point 6 of the hook to dimension D. Then
securely tighten setscrew A 4 and setscrew B 8.
4. Turn the handwheel and move the screw gear (large) to the
right or left so that needle 5 aligns with blade point 6 of the
hook when needle bar 1 is raised from the lowest dead point
of its stroke to dimension B. Then tighten two setscrews 3.
5. Turn the handwheel and loosen clamping screw 2 in the needle
bar holder to adjust so that the distance from the top end of the
eyelet of needle 5 to blade point 6 of the hook becomes
dimension C when needle bar 1 is raised from the lowest dead
point of its stroke to dimension B. Then tighten again the
clamping screw. (For LU-1510N-7, there is an engraved marker
line in needle bar 1.) However, in case of LU-1565N, loosen
clamping screws 9 and !0 and turn needle clamp !1 to adjust.
Then tighten again the clamping screws. The range to turn
needle clamp !1 is as wide as the clearance between the width
of long hole of needle bar 1 and clamping screw !0.
6. Set the stitch dial to the maximum and check that needle 5
does not come in contact with blade point 6 of the hook. (For
the dimension, refer to the respective models in the list.)
3) Adjusting the needle guard of the hook
1. Bend needle guard 7 and adjust so that the needle guard 7
comes in contact 0.1 to 0.2 mm with the needle.
(Caution) 1. After tightening the hook shaft screw gear,
check that the hook shaft has no thrust play.
2. Check that the hook shaft screw gear has
backlash.
3. In case of 2-needle. left and right are the same
adjustment value.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the JUKI LU-1511N-7 and is the answer not in the manual?

JUKI LU-1511N-7 Specifications

General IconGeneral
BrandJUKI
ModelLU-1511N-7
CategorySewing Machine
LanguageEnglish

Related product manuals