--
FE
OPERAT~OK
-
--
CAUTION:
To avoid malfunction and damage of the machine, confirm the following.
Before you put the machine into operation for the first time after the set-up, clean it thoroughly.
Remove all dust gathering during transportation and oil it well.
Confirm that the voltage has been correctly set.
I
Confirm that the power plug has been properly connected to the power supply.
I
I
Never use the machine in the state where the voltage type is different from the designated one.
I
I
Confirm that the direction of rotation of the motor pulley is correct.
I
I
Before applying power, release the stop-motion mechanism and turn by hand the needle driving pulley
1
I
in order to ensure that the machine is in order.
1
I
To install the machine, the frame support bar has to
be
firstly inserted into the table.
1
WARNING:
Turn
OFF
the power before starting the work so as to prevent accidents
I
caused by abrupt start of the sewing machine.
Put
rabber
cushion
0
on the table,
place the
machne head on the rubber
cushion and fix it to the table using
screws
@
,
plain washers
@
and nuts
@
.
Attach
"S"
chain hook
@
and
chain
to stop motion trip lever
@
.
1.
Apply
JUKI
New Defrix
Oil
NO.
1
to the components shown by the arrows. (Once
or twice a week)
2.
Loosen connecting screw
0
,
tilt the head backward and apply some grease to
driving worm gear
@
and gear
9
.
3.
Check, approximately once a week, that oil amount
is
sufficient to reach the top of
the oil felt placed inside the bed mounting base. If the amount of oil is insufficient,
add an adequate amount of oil. At this time, also apply oil to crank rod
@
.
I
1.
INSTALLATION OF
MACHINE HEAD
1
3.
ATTACHING THE NEEDLE
I
2.
LUBRICATION
1
WARNING:
Turn
OFF
the power before starting the work so as
to prevent accidents caused by abrupt start
of
the
sewing machine.
-
J
7
*
Turn OFF the
power
to
/
the motor.
1
*
Use
a
standard
needle
;
ofTQx?*!hfor.ViH-
,
172
and
TQx-
5111
!:,I
!
1
MS-373.
,
Q/
1
,,
I
!
1.0c1sr.11
ccreb
@
,
,
.
Inserr
::t:edlc.
i!,,
i
.
'
:
,/
f-;
into
if!?
:ler..i!c.
!i)..::.
.,'
<i
.:-,
:
,
ihz
ne~ciir
h3:
:in:ll
i;
I
i
c--
j
cornes
:!:
ion:lt,t
w;i;l
!he
c'.t.ry;;:
:-!:(I
,>:
needie
i:'
.I:.
3.
.ri.gi~t~il
,;.ii!i,
a
i::::i~;
4.
ATTACHING THE NEEDLE
!
BAR GUARD
WARNING:
Turn
OFF
the power before starting the work so as
to prevent accidents caused by abrupt start of the
A
sewing machine.
-
--
!
2
1. Loose11
screw
@
~nd
remove
;hc
ihrea,.!
:L~LII~?
No.
2.
2.
Place
riei.:li-
has
g,;i:.!<
Q
kinder
ti,.
ti-r*::id
gu:(j,,.
'.',..
-
~nd
r.tl,d,:-
:-::i-
i:';lrci
@
toge!hcr
:i
.!ilg
~cie'r-
$.
(Notes)
If
your
machine has
a
wiper
mn:jnet,
attach
the
needle
bar
guard
on
to
the
wiper
magnst
base.
To Next Page
Loading...
