To Next PageTo Next PageWhy do seams flute or wave on my JUKI MO-735 when sewing knits?
If the seams flute or wave, especially when sewing knits with your JUKI Sewing Machine, avoid pulling the fabric while sewing; guide it gently. Also, check if the presser foot pressure is too tight and reduce it if necessary. Finally, ensure that the differential feed is set correctly; adjust it to N - 2.
What to do if my JUKI Sewing Machine skips stitches?
If you're experiencing skipped stitches with your JUKI Sewing Machine, start by replacing the needles if they are bent or blunt. Ensure you are using the correct needle system, such as 130/705H or JLx2. Also, try increasing the presser foot pressure.
Why is my JUKI MO-735 skipping stitches?
If your JUKI Sewing Machine is skipping stitches, ensure that the needles are not bent or blunt and replace them if necessary. Also, make sure you're using the correct needle system 130/705H, and type JLx2 for cover and chainstitch. If the presser foot pressure is too low, increase it.
Why does the thread keep breaking on my JUKI Sewing Machine?
If your JUKI Sewing Machine thread breaks, it might be due to several reasons. The thread tension could be too tight for the thread you're using, so try reducing the thread tension. Also, double-check that the machine is threaded correctly. Ensure the needles are correctly inserted fully into the needle clamp with the flat side to the back. Finally, make sure you're using the correct needles, specifically needle system 130/705H or JLx2.
How to fix poor stitch formation on my JUKI MO-735?
If you notice poor stitch formation on your JUKI Sewing Machine, make sure the threads are correctly positioned between the tension dials. Check if the thread is lying between the tension discs. Also, ensure the thread hasn't gotten caught; raise the presser foot and gently pull the thread to release it. Finally, verify the threading path of each thread to ensure the machine is threaded correctly.
How to fix a JUKI Sewing Machine that does not sew?
If your JUKI Sewing Machine is not sewing, make sure that the looper or cloth plate cover is closed. Also, check that the main switch is turned on (set to “I”).
Why do needles break on my JUKI MO-735?
If your JUKI Sewing Machine needles are breaking, replace them if they are bent, blunt, or have damaged points. Ensure that the needles are fully inserted into the needle clamp with the flat side to the back. Also, guide the fabric gently with both hands instead of pulling it while sewing.
What to do if the thread loops are too loose on my JUKI MO-735?
To resolve loose thread loops on your JUKI Sewing Machine, ensure there is enough fabric in the stitch by increasing the cutting width.
Why are the seams puckering on my JUKI MO-735?
If the seams on your JUKI Sewing Machine are puckering, it could be because the needle thread tension is too tight. Try reducing the needle thread tension. Also, check the differential feed setting and adjust it to 0.7 - N.
Why is the fabric not feeding evenly through my JUKI MO-735?
If the fabric is not feeding evenly through your JUKI Sewing Machine, it could be due to a few reasons. First, check the differential feed setting to ensure it is properly adjusted. Next, verify that the presser foot pressure is not too low and adjust it if necessary. Finally, inspect the lower and upper knives; if they are blunt or wrongly positioned, replace them.
General| Number of Threads | 2/3/4/5 |
|---|---|
| Maximum Stitch Length | 4 mm |
| Stitch Length Range | 1-4 mm |
| Differential Feed | Yes |
| Differential Feed Ratio | 0.7-2.0 |
| Rolled Hem | Yes |
| Cover Stitch Capability | Yes |
| Needle Type | 130/705H |
| Overlocking Width | 5-9 mm |
| Maximum Sewing Speed | 1, 500 stitches per minute |
| Thread Tension | Manual |
| Presser Foot Lift | 5 mm |
| Stitch Options | Rolled Hem |
| Power Requirements | 120V AC, 60Hz |
| Weight | 19.4 lbs |
