JVC 70 Series User Manual

cok
set: Press‘Ci
CAPTION to turn it
off.
DISPLAY
The Display screen shows the current
status of timers and inputs.
DISPLAY
eee
The display shows the following:
Q The current channel or AV input
(Channel 07)
Q Current time (12:20 PM)
Q Sleep Timer status minutes remain-
ing (OFF)
QO On/Off Timer status (Everyday, on at
7:00 PM, off at 10:00 PM)
0 Each press of the Disptay button
changes the display mode:
eee alla CHANNEL—> OFF
CLOSED CAPTION
View the closed captions or text when
included in a program.
CLOSED CAPTION
l > co —> text —> OFF>> |
O To change caption or text channels
see pages 20 and 21.
Q) To access a captioning option or fo turn
one off, allow the display to remain on
screen until it disappears. In seconds
the captions or text will start.
ba) BUTTON FUNCTIONS
VIDEO STATUS
The Video Status button lets you select the
“Choice” settings of the Set Video Status
menu, Theater Status or reset to factory
settings.
“Standard” resets the picture settings
to factory standard levels.
“Choice” consists of the settings that you
saved in the Set Video Status menu, see
page 17.
“Theater” for a film-like look to video.
VipEO STATUS
ei —> THEATER —> STANDARD “a
Cap SLEEP TIMER
Sleep Timer turns off the TV for you in
case you fall asleep. Program it to work
in intervals of 15 minutes up to 180.
SLEEP TIMER
[‘ 15 30 45 60 75 90 105 120 135 150 165 a
€ € <
SLEEP TIMER MESSAGE:
20 seconds prior to the automatic
shut-off, this message will appear:
You then have 20 seconds to press
the Sleep Timer button to delay turn
off for another 15 minutes.
BUTTON FUNCTIONS {|
HYPER SURROUND
Create a deep, 3-Dimensional sound
effect by channeling the sound
through the TV's front firing speakers.
Technically speaking, Hyper Surround,
manipulates the phase and frequency
response of stereo signals to make
the sound seem to come out into the
room without using rear speakers.
100 +
The 100+ button accesses all channels
above Channel 99.
To move to Channel 124:
100+
CEES) 2 (two)
4 (four)
VCR BUTTONS
Your JVC remote will control your
VCR. You can play, rewind and fast-
forward, record, pause, stop, channel
scan, and power on and off.
© The remote is preset to control a JVC
VCR, Put in the code 00 for a JVC
brand VCR. For any other brand, you
must set the manufacturer's code (see
pages 12 and 13).
TV /VIDEO
TV/Video selects the input mode.
TV VIDEO
? TV. —— > vIDEO-1 > vidEo-2 a
MUTE
The Mute button turns the sound off
completely when you press it. Press it
again to restore the sound to the
previous level.
Retumi, ‘go to- :
page 11.
RETURN+
There are two kinds of Return, regular
and Return+.
Return+. You can set a “return” channel
to come back to when you scan with
CHANNEL -/+.
ReTurn+ and hold for 3 seconds
Scan through the channels
with the CHANNEL -/+ button
RETuarn+ to go back to the
return channel
© Pressing a number key or turning
the TV's power off cancels Return+.
© See page 11 for more information.
Return. You can return to a channel after
moving to another channel via the 10
key pad.
RETURN+
Move to another channel
BESS) RETURN+
NUMBER BUTTONS
10 KEY PAD
The Number Buttons are from 0 to 9. Press
two number buttons to go to a channel.
To move to Channel 7:
0 (zero)
7 (seven)

JVC 70 Series Specifications

General

Brand	JVC
Model	70 Series
Category	TV
Language	English